欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TPA6203A1ZQVRG1
廠商: TEXAS INSTRUMENTS INC
元件分類: 音頻/視頻放大
英文描述: 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8
封裝: 2 X 2 MM, GREEN, PLASTIC, BGA-8
文件頁數: 5/29頁
文件大小: 952K
代理商: TPA6203A1ZQVRG1
FULLY DIFFERENTIAL AMPLIFIER
V(LRMS)
VO
IDD
IDD(avg)
Efficiency of a BTL amplifier +
P
L
P
SUP
where:
P
L +
V
L
rms2
R
L
, and V
LRMS +
V
P
2
, therefore, P
L +
V
P
2
2R
L
PL = Power delivered to load
PSUP = Power drawn from power supply
VLRMS = RMS voltage on BTL load
RL = Load resistance
VP = Peak voltage on BTL load
IDDavg = Average current drawn from the
power supply
VDD = Power supply voltage
ηBTL = Efficiency of a BTL amplifier
and PSUP + VDD IDDavg and IDDavg +
1
p
0
V
P
R
L
sin(t) dt
+
1
p
V
P
R
L
[cos(t)]
p
0 +
2V
P
p
R
L
Therefore,
P
SUP +
2 V
DD
V
P
p
R
L
substituting PL and PSUP into equation 6,
Efficiency of a BTL amplifier +
V
P
2
2 R
L
2 V
DD VP
p
R
L
+
p
V
P
4 V
DD
V
P +
2 P
L
R
L
where:
(6)
www.ti.com.......................................................................................................................................................... SLOS364F – MARCH 2002 – REVISED JUNE 2008
EFFICIENCY AND THERMAL INFORMATION
Class-AB amplifiers are inefficient. The primary cause
of these inefficiencies is voltage drop across the
output stage transistors. There are two components
of the internal voltage drop. One is the headroom or
dc voltage drop that varies inversely to output power.
The second component is due to the sinewave nature
of the output. The total voltage drop can be
calculated by subtracting the RMS value of the output
voltage from VDD. The internal voltage drop multiplied
by the average value of the supply current, IDD(avg),
determines the internal power dissipation of the
amplifier.
Figure 33. Voltage and Current Waveforms for
BTL Amplifiers
An easy-to-use equation to calculate efficiency starts
out as being equal to the ratio of power from the
power supply to the power delivered to the load. To
Although the voltages and currents for SE and BTL
accurately calculate the RMS and average values of
are sinusoidal in the load, currents from the supply
power in the load and in the amplifier, the current and
are
very
different
between
SE
and
BTL
voltage waveform shapes must first be understood
configurations. In an SE application the current
(see Figure 33).
waveform is a half-wave rectified shape, whereas in
BTL it is a full-wave rectified waveform. This means
RMS conversion factors are different. Keep in mind
that for most of the waveform both the push and pull
transistors are not on at the same time, which
supports the fact that each amplifier in the BTL
device only draws current from the supply for half the
waveform. The following equations are the basis for
calculating amplifier efficiency.
Copyright 2002–2008, Texas Instruments Incorporated
13
Product Folder Link(s): TPA6203A1
相關PDF資料
PDF描述
TPA6203A1DRBG4 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC8
TPA6203A1DRBRG4 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC8
TPA6203A1DRBR 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC8
TPA6203A1DRB 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC8
TPA6203A1DGNR 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8
相關代理商/技術參數
參數描述
TPA6204A1 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.7W MONO FULLY DIFFERENTIAL AUDIO POWER AMPLIFIER
TPA6204A1_07 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.7W MONO FULLY DIFFERENTIAL AUDIO POWER AMPLIFIER
TPA6204A1DGN 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.7W MONO FULLY DIFFERENTIAL AUDIO POWER AMPLIFIER
TPA6204A1DRB 功能描述:音頻放大器 1.7-W Mono Full Diff Aud Power Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TPA6204A1DRB 制造商:Texas Instruments 功能描述:AUDIO POWER AMPLIFIER IC 制造商:Texas Instruments 功能描述:IC, AUDIO PWR AMP, CLASS AB, 1.7W, SON-8
主站蜘蛛池模板: 阿勒泰市| 黎城县| 芮城县| 罗山县| 宜君县| 钦州市| 耒阳市| 稻城县| 金阳县| 张家港市| 长子县| 犍为县| 长阳| 双鸭山市| 延安市| 栖霞市| 皮山县| 通许县| 洞口县| 涿鹿县| 樟树市| 新乡县| 北辰区| 上犹县| 礼泉县| 江口县| 长武县| 晋中市| 黄陵县| 彰化市| 平远县| 明水县| 绥中县| 石城县| 凌源市| 阜新市| 博客| 监利县| 酒泉市| 枝江市| 金阳县|