- 您現在的位置：買賣IC網 > PDF目錄382673 > TPIC0108BDWP (Texas Instruments, Inc.) CONNECTOR ACCESSORY PDF資料下載
參數資料
| 型號： | TPIC0108BDWP |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | CONNECTOR ACCESSORY |
| 中文描述： | 連接器附件 |
| 文件頁數： | 9/14頁 |
| 文件大小： | 205K |
| 代理商： | TPIC0108BDWP |
TPIC0108B
PWMCONTROL INTELLIGENT H-BRIDGE
SLIS068 – NOVEMBER1998
9
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
protective functions and diagnostics
over current/short circuit
The TPIC0108B detects shorts to V
CC
, ground, or across the load being driven, by comparing the V
DS
voltage
drop across the DMOS outputs against the threshold voltage. The DMOS outputs of the TPIC0108B will be
disabled and the fault flags will be generated 10
μ
s after an over-current or short-circuit fault is detected. This
10
μ
s delay is long enough to serve as a de-glitch filter for high current transients, yet short enough to prevent
damage to the DMOS outputs. The DMOS outputs remain latched off until either IN1 or IN2 input is toggled.
In cases where the outputs have a continuous short-to-ground or when enabled from quiescent mode with a
short-to-ground already exists (current rise time faster than 0.5 A/
μ
s in both instances), the over-current
shutdown threshold will decrease to 3 A to reduce power dissipation. This reduction to 3 A is achieved since
the DMOS outputs will not be fully enhanced when the over-current threshold is reached if the current rise time
exceeds 0.5 A/
μ
s. Over-current and/or short-circuit protection is provided up to V
CC
= 16.5 V and a junction
temperature of 90
°
C.
over temperature
The TPIC0108B disables all DMOS outputs and the fault flags will be set when T
J
≥
140
°
C (min.). The DMOS
outputs remain latched off until either IN1 or IN2 input is toggled.
under voltage
The TPIC0108B disables all DMOS outputs when V
CC
≤
V
(UVCC)
. The outputs will be re-enabled when
V
CC
≥
V
(UVCC)
. No fault flags are set when under-voltage lockout occurs.
over voltage
In order to protect the DMOS outputs from damage caused by excessive supply voltage, the TPIC0108B
disables all outputs when V
CC
≥
V
(OVCC)
. Once V
CC
≤
V
(OVCC)
, either IN1 or IN2 input must be toggled to
re-enable the DMOS outputs.
cross conduction
Monitoring circuitry for each transistor detects whether the particular transistor is active to prevent the HSD or
LSD of the corresponding half H-bridge from conducting.
open circuit
During operation, the bridge current is controlled continuously. If the bridge current is >10 mA (min.) for a period
>1 ms (min.), the fault flags are set. However, the output transistors will not be disabled.
All limits mentioned are typical values unless otherwise noted.
If a short circuit occurs (i.e., the over-current detection circuitry is activated) at a supply voltage higher than 16.5 V and a junction temperature
higher than 90
°
C, damage to the device may occur.
相關PDF資料 |
PDF描述 |
|---|---|
| TPIC2406MJB | Quad Peripheral Driver |
| TPIC2406NE | Quad Peripheral Driver |
| TPIC2701J | TRANSISTOR | MOSFET | ARRAY | N-CHANNEL | 60V V(BR)DSS | DIP |
| TPIC2801AKV | Octal Peripheral Driver |
| TPIC2801KV | Octal Peripheral Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPIC0108BDWPR | 功能描述:INTEL H-BRIDGE 180 MOHM 20-HSOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| TPIC0109RTYR | 制造商:Texas Instruments 功能描述:DRIVER-NON VMI |
| TPIC0110RTYR | 制造商:Texas Instruments 功能描述: |
| TPIC0298 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL FULL-H DRIVER |
| TPIC0298KV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC Motor Controller/Driver |
發布緊急采購，3分鐘左右您將得到回復。