欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TPS2201YDF
廠商: Texas Instruments, Inc.
英文描述: DUAL-SLOT PC CARD POWER-INTERFACE SWITCHES FOR PARALLEL PCMCIA CONTROLLERS
中文描述: 雙插槽PC卡電源接口開關并聯的PCMCIA控制器
文件頁數: 16/23頁
文件大小: 478K
代理商: TPS2201YDF
TPS2201, TPS2201Y
DUAL-SLOT PC CARD POWER-INTERFACE SWITCHES
FOR PARALLEL PCMCIA CONTROLLERS
SLVS094B – AUGUST 1994 – REVISED AUGUST 1995
6–16
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
voltage transitioning requirement (continued)
capacitors on 3.3-V compatible cards be discharged to below 0.8 V before applying 3.3-V power. This ensures
that sensitive 3.3-V circuitry is not subjected to any residual 5-V charge and functions as a power reset. The
TPS2201 offers a selectable V
CC
and V
PP
ground state, per PCMCIA 3.3-V/5-V switching specifications, to fully
discharge the card capacitors while switching between V
CC
voltages.
output ground switches
Several PCMCIA power-distribution switches on the market do not have an active-grounding FET switch. These
devices do not meet the PC Card specification requiring a discharge of V
CC
within 100 ms. PC Card resistance
can not be relied on to provide a discharge path for voltages stored on PC Card capacitance because of possible
high-impedance isolation by power-management schemes. A method commonly shown to alleviate this
problem is to add to the switch output an external 100 k
resistor in parallel with the PC Card. Considering that
this is the only discharge path to ground, a timing analysis will reveal that the RC time constant delays the
required discharge time to over 2 seconds. The only way to ensure timing compatibility with PC Card standards
is to use a power-distribution switch that has an internal ground switch, like that of the TPS22xx family, or add
an external ground FET to each of the output lines with the control logic necessary to select it.
In summary, the TPS2201 is a complete single-chip dual-slot PC Card power interface. It meets all currently
defined PCMCIA specifications for power delivery in 5-V, 3.3-V, and mixed systems, and offers a serial controller
interface. The TPS2201 offers functionality, power savings, overcurrent and thermal protection, and fault
reporting in one 30-pin SSOP surface-mount package for maximum value added to new portable designs.
power supply considerations
The TPS2201 has multiple terminals for each of its 3.3 V, 5 V, and 12 V power inputs and for the switched V
CC
outputs. Any individual terminal can conduct the rated input or output current. Unless all terminals are connected
in parallel, the series resistance is significantly higher than that specified, resulting in increased voltage drops
and lost power. Both 12 V inputs must be connected for proper V
pp
switching; it is recommended that all input
and output power terminals be paralleled for optimum operation. The V
DD
input lead must be connected to the
5V input leads.
Although the TPS2201 is fairly immune to power input fluctuations and noise, it is generally considered good
design practice to bypass power supplies typically with a 1-
μ
F electrolytic or tantalum capacitor paralleled by
a 0.047-
μ
F to 0.1-
μ
F ceramic capacitor. It is strongly recommended that the switched V
CC
and V
pp
outputs be
bypassed with a 0.1-
μ
F or larger capacitor; doing so improves the immunity of the TPS2201 to electrostatic
discharge (ESD). Care should be taken to minimize the inductance of PCB traces between the TPS2201 and
the load. High switching currents can produce large negative-voltage transients, which forward biases substrate
diodes, resulting in unpredictable performance.
The TPS2201, unlike other PC Card power-interface switches, does not use the 12-V power supply for switching
or other chip functions. Instead, an internal charge pump generates the necessary voltage from V
DD
, allowing
the 12-V input supply to be shut down except when the V
pp
programming or erase voltage is needed. Careful
system design making use of this feature reduces power consumption and extends battery lifetime.
The 3.3-V power input should not be taken higher than the 5-V input. Doing so, though nondestructive, results
in high current flow into the device, and could result in abnormal operation. In any case, this occurrence indicates
a malfunction of one input voltage or both, which should be investigated.
Similarly, no terminal should be taken below –0.3 V; forward biasing the parasitic-substrate diode results in
substrate currents and unpredictable performance.
相關PDF資料
PDF描述
TPS2201YDB DUAL-SLOT PC CARD POWER-INTERFACE SWITCHES FOR PARALLEL PCMCIA CONTROLLERS
TPS2201DB DUAL-SLOT PC CARD POWER-INTERFACE SWITCHES FOR PARALLEL PCMCIA CONTROLLERS
TPS2201DF DUAL-SLOT PC CARD POWER-INTERFACE SWITCHES FOR PARALLEL PCMCIA CONTROLLERS
TPS2201Y Terminal Block; Pitch Spacing:0.2"; Wire Size (AWG):26-14; Mounting Type:PC Board; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No
TPS2202YDF DUAL-SLOT PC CARD POWER-INTERFACE SWITCHES FOR SERIAL PCMCIA CONTROLLERS
相關代理商/技術參數
參數描述
TPS2202AIDB 功能描述:熱插拔功率分布 1A Dual-Slot PC Card Pwr Sw RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2202AIDBG4 功能描述:熱插拔功率分布 1A Dual-Slot PC Card Pwr Sw RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2202AIDBLE 制造商:Rochester Electronics LLC 功能描述:- Bulk
TPS2202AIDBR 功能描述:熱插拔功率分布 1A Dual-Slot PC Card w/Serial Interface RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2202AIDBRG4 功能描述:熱插拔功率分布 1A Dual-Slot PC Card w/Serial Interface RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
主站蜘蛛池模板: 共和县| 游戏| 鹰潭市| 衡山县| 隆化县| 疏附县| 巴彦县| 阿巴嘎旗| 洛隆县| 老河口市| 古田县| 宁城县| 木里| 哈尔滨市| 县级市| 磐安县| 宝兴县| 蒙山县| 台中县| 东乡县| 黔西县| 尤溪县| 祁阳县| 海兴县| 元朗区| 宁晋县| 共和县| 邓州市| 乌兰县| 榆社县| 全南县| 青龙| 眉山市| 庆元县| 永顺县| 金昌市| 南郑县| 海丰县| 印江| 涟水县| 怀宁县|