- 您現在的位置：買賣IC網 > PDF目錄382675 > TPS3106H33DVBR (Texas Instruments, Inc.) Circular Connector; MIL SPEC:MIL-C-26482, Series I, Crimp; Body Material:Aluminum; Series:PT06; Number of Contacts:5; Connector Shell Size:18; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight PDF資料下載
參數資料
| 型號： | TPS3106H33DVBR |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; MIL SPEC:MIL-C-26482, Series I, Crimp; Body Material:Aluminum; Series:PT06; Number of Contacts:5; Connector Shell Size:18; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight |
| 中文描述： | 超低電源電流/電源電壓監控電路 |
| 文件頁數： | 9/22頁 |
| 文件大小： | 361K |
| 代理商： | TPS3106H33DVBR |
SLVS363B AUGUST 2001 REVISED SEPTEMBER 2004
www.ti.com
9
Terminal Functions
TERMINAL
I/O
DESCRIPTION
NAME
PART
ALL
NO.
2
GND
GND
MR
ALL
3
I
Manual-reset input. Pull low to force a reset. RESET remains low as long as MR is low
and for the timeout period after MR goes high. Leave unconnected or connect to VDD
when unused.
PFI
TPS3103
4
I
Power-fail input compares to 0.551 V with no additional delay. Connect to VDD if not used.
Power-fail output. Goes high when voltage at PFI rises above 0.551 V.
PFO
TPS3103
5
O
RESET
TPS3103
TPS3110
1
O
Active-low reset output. Either push-pull or open-drain output stage
RSTSENSE
TPS3106
5
O
Active-low reset output. Logic level at RSTSENSE only depends on the voltage at
SENSE and the status of MR.
RSTVDD
TPS3106
1
O
Active-low reset output. Logic level at RSTVDD only depends on the voltage at VDD and
the status of MR.
SENSE
TPS3106
TPS3110
4
4
I
A reset will be asserted if the voltage at SENSE is lower than 0.551 V. Connect to VDD if
unused
VDD
WDI
ALL
6
Supply voltage. Powers the device and monitors its own voltage
TPS3110
5
I
Watchdog timer input. If WDI remains high or low longer than the time-out period, then
reset is triggered. The timer clears when reset is asserted or when WDI sees a rising
edge or a falling edge.
detailed description
watchdog
The TPS3110 device integrates a watchdog timer that must be periodically triggered by a positive or negative
transition of WDI. When the supervising system fails to retrigger the watchdog circuit within the time-out interval,
RESET becomes active for the time period (t
d
). This event also reinitializes the watchdog timer.
manual reset (MR)
Many
μ
C-based products require manual-reset capability, allowing an operator or logic circuitry to initiate a
reset. Logic low at MR asserts reset. Reset remains asserted while MR is low and for a time period (t
d
) after
MR returns high. The input has an internal 100-k
pull-up resistor, so it can be left open if it is unused.
Connect a normally open momentary switch from MR to GND to create a manual reset function. External
debounce is not required. If MR is driven from long cables or if the device is used in noisy environments,
connecting a 0.1-
μ
F capacitor from MR to GND provides additional noise immunity.
PFI, PFO
The TPS3103 has an integrated power-fail (PFI) comparator with a separate open drain (PFO) output can be
used for low-battery detection, power-fail warning, or for monitoring a power supply other than the main supply.
An additional comparator is provided to monitor voltages other than the nominal supply voltage. The power-fail
input (PFI) will be compared with an internal voltage reference of 0.551 V. If the input voltage falls below the
power-fail threshold (V
IT(S)
), the power-fail output (PFO) goes low. If it goes above 0.551 V plus approximately
15-mV hysteresis, the output returns to high. By connecting two external resistors, it is possible to supervise
any voltage above 0.551 V. The sum of both resistors should be approximately 1 M
, to minimize power
consumption and to assure that the current into the PFI pin can be neglected compared with the current through
the resistor network. The tolerance of the external resistors should be not more than 1% to ensure minimal
variation of sensed voltage. If the power-fail comparator is unused, connect PFI to GND and leave PFO
unconnected. For proper operation of the PFI-comparator the supply voltage (V
DD
) must be higher than 0.8 V.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS3106K12DVBR | ULTRALOW SUPPLY CURRENT/SUPPLY VOLTAGE SUPERVISORY CIRCUITS |
| TPS3110K12DVBR | ULTRALOW SUPPLY CURRENT/SUPPLY VOLTAGE SUPERVISORY CIRCUITS |
| TPS3110H33DVB | ULTRALOW SUPPLY CURRENT/SUPPLY VOLTAGE SUPERVISORY CIRCUITS |
| TPS3103K33DVB | ULTRALOW SUPPLY CURRENT/SUPPLY VOLTAGE SUPERVISORY CIRCUITS |
| TPS3106K33DVB | ULTRALOW SUPPLY CURRENT/SUPPLY VOLTAGE SUPERVISORY CIRCUITS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS3106K09DVB | 制造商:TI 制造商全稱:Texas Instruments 功能描述:ULTRALOW SUPPLY CURRENT/SUPPLY VOLTAGE SUPERVISORY CIRCUITS |
| TPS3106K09DVBR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:ULTRALOW SUPPLY CURRENT/SUPPLY VOLTAGE SUPERVISORY CIRCUITS |
| TPS3106K12DVB | 制造商:TI 制造商全稱:Texas Instruments 功能描述:ULTRALOW SUPPLY CURRENT/SUPPLY VOLTAGE SUPERVISORY CIRCUITS |
| TPS3106K12DVBR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:ULTRALOW SUPPLY CURRENT/SUPPLY VOLTAGE SUPERVISORY CIRCUITS |
| TPS3106K15DVB | 制造商:TI 制造商全稱:Texas Instruments 功能描述:ULTRALOW SUPPLY CURRENT/SUPPLY VOLTAGE SUPERVISORY CIRCUITS |
發布緊急采購，3分鐘左右您將得到回復。