- 您現在的位置：買賣IC網 > PDF目錄98280 > TPS3618-50DGKT (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | TPS3618-50DGKT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | 3.05 X 4.98 MM, GREEN, PLASTIC, MSOP-8 |
| 文件頁數： | 2/16頁 |
| 文件大小： | 455K |
| 代理商： | TPS3618-50DGKT |
www.ti.com
DETAILED DESCRIPTION
BATTERY FRESHNESS SEAL (TPS3617 Only)
POWER-FAIL COMPARATOR (PFI AND PFO)
WATCHDOG
VIT
WDI
RESET
td
t(tout)
VOUT
td
Undefined
SLVS339D – DECEMBER 2000 – REVISED DECEMBER 2006
The battery freshness seal of the TPS3617 family disconnects the backup battery from the internal circuitry until
it is needed. This ensures that the backup battery connected to VBAT should be fresh when the final product is
put to use. The following steps explain how to enable the freshness seal mode:
1. Connect VBAT (VBAT > VBAT(min)).
2. Ground PFO.
3. Connect PFI to VDD (PFI = VDD).
4. Connect VDD to power supply (VDD > VIT) and keep connected for 5 ms < t < 35 ms.
The battery freshness seal mode is disabled by the positive-going edge of RESET when VDD is applied.
An additional comparator monitors voltages other than the nominal supply voltage. The power-fail-input (PFI)
can be compared with an internal voltage reference of 1.15 V. If the input voltage falls below the power-fail
threshold (V(PFI)) of 1.15 V typical, the power-fail output (PFO) goes low. If it goes above V(PFI) plus about 12-mV
hysteresis, the output returns to high. By connecting two external resistors it is possible to supervise any
voltages above V(PFI). The sum of both resistors should be about 1 M, to minimize power consumption and
also to ensure that the current in the PFI pin can be neglected compared with the current through the resistor
network. The tolerance of the external resistors should be not more than 1% to ensure minimal variation of the
sensed voltage. If the power-fail comparator is unused, connect PFI to ground and leave the PFO unconnected.
In a microprocessor- or DSP-based system, it is not only important to supervise the supply voltage, it is also
important to ensure correct program execution. The task of a watchdog is to ensure that the program is not
stalled in an indefinite loop. The microprocessor, microcontroller, or DSP has to toggle the watchdog input within
0.8 s typically, to avoid a timeout from occurring. Either a low-to-high or a high-to-low transition resets the
internal watchdog timer. If the input is unconnected, the watchdog is disabled and should be retriggered
internally. See Figure 13 for the watchdog timing diagram.
Figure 13. Watchdog Timing
10
相關PDF資料 |
PDF描述 |
|---|---|
| TPS3705-33Y | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, UUC8 |
| TPS3803-01DCKRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3805H33DCKR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3803G15DCKRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TPS3803G15QDCKRQ1 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS3618-50DGKTG4 | 功能描述:監控電路 5-V Battery-Backup for RAM Retention RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| TPS3619-33 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:備份電池監督員保留內存 |
| TPS3619-33DGK | 功能描述:監控電路 Battery-Backup for RAM Retention RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| TPS3619-33DGK | 制造商:Texas Instruments 功能描述:IC's |
| TPS3619-33DGKG4 | 功能描述:監控電路 Battery-Backup for RAM Retention RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。