- 您現在的位置：買賣IC網 > PDF目錄98281 > TPS40074RHL (TEXAS INSTRUMENTS INC) 2 A SWITCHING CONTROLLER, 550 kHz SWITCHING FREQ-MAX, PQCC20 PDF資料下載
參數資料
| 型號： | TPS40074RHL |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 2 A SWITCHING CONTROLLER, 550 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | PLASTIC, QFN-20 |
| 文件頁數： | 6/37頁 |
| 文件大小： | 448K |
| 代理商： | TPS40074RHL |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
www.ti.com
VDG03173
T2
T1
T3
T1
VSW
VIN 2V
IILIM
VILIM Threshold
(A)
(B)
TPS40074
SLUS617–APRIL 2005
APPLICATION INFORMATION (continued)
In addition, just prior to the high-side MOSFET turning on, the ILIM pin is pulled down to approximately half of
VDD. The ILIM pin is allowed to return to its nominal value after one of two events occur:
1. The SW node rises to within approximately 2 V of VDD
2. An internal timeout occurs, approximately 125-ns after ILIM is initially pulled down
If the SW node rises to within approximately 2-V of VDD, the device allows ILIM to go back to its nominal value.
This is illustrated in Figure 10 A. T1 is the delay time from the internal PWM signal being asserted and the rise of
SW. This includes the driver delay of 50 ns typical, and the turn on time of the high-side MOSFET. The MOSFET
used should have a turn on time less than 75 ns. T2 is the reaction time of the sensing circuit that allows ILIM to
start to return to its nominal value, typically 20ns.
The second event that can cause ILIM to return to its nominal value is for an internal timeout to expire. This is
illustrated in Figure 10 B as T3. Here SW never rises to VDD-2, for whatever reason, and the internal timer times
out. This allows the ILIM pin to start its transition back to its nominal value.
Prior to ILIM starting back to its nominal value, short circuit sensing is not enabled. In normal operation, this
insures that the SW node is at a higher voltage than ILIM when short circuit sensing starts, avoiding false trips
while allowing for a quicker blanking delay than would ordinarily be possible. Placing a capacitor across RILIM
sets an exponential approach to the normal voltage at the ILIM pin. This exponential “decay” of the short circuit
threshold can be used to compensate for ringing on the SW node after its rising edge and to help compensate
for slower turn-on MOSFETs. Choosing the proper capacitance requires care. If the capacitance is too large, the
voltage at ILIM does not approach the desired short circuit level quickly enough, resulting in an apparent shift in
short circuit threshold as pulse width changes.
The comparator that looks at ILIM and SW to determine if a short circuit condition exists has a clamp on its SW
input. This clamp makes the SW node never appear to fall more than 1.4 V (approximately, could be as much as
2 V at – 40°C) below VDD. While ILIM is more than 1.4 V below VDD short circuit sensing is effectively disabled,
giving a programmable absolute blanking time. As a general rule, it is best to make the time constant of the R-C
at the ILIM pin 20% or less of the nominal pulse width of the converter (See Equation 11)
Figure 10. Voltage Feed-Forward and PWM Duty Cycle Waveforms
The second tier protection incorporates a fault counter. The fault counter is incremented on each cycle with an
overcurrent pulse and decremented on a clock cycle without an overcurrent pulse. When the counter reaches
seven (7) a fault condition is declared by the controller. When this happens, the output drivers turn both
14
相關PDF資料 |
PDF描述 |
|---|---|
| TPS40075RHLR | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS40075RHLTG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS40077PWPR | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40077PWPRG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40077PWPG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS40074RHLR | 功能描述:DC/DC 開關控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40074RHLRG4 | 功能描述:DC/DC 開關控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40074RHLT | 功能描述:DC/DC 開關控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40074RHLTG4 | 功能描述:DC/DC 開關控制器 Mid Input Sync Buck w/Vltg Feed-Fwd RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40075 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4.5V TO 18V INPUT 10 PIN SYNCHRONOUS BUCK CONTROLLER WITH POWER GOOD |
發布緊急采購，3分鐘左右您將得到回復。