- 您現在的位置：買賣IC網 > PDF目錄98281 > TPS40131RHBTG4 (TEXAS INSTRUMENTS INC) SWITCHING CONTROLLER, 1200 kHz SWITCHING FREQ-MAX, PQCC32 PDF資料下載
參數資料
| 型號： | TPS40131RHBTG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 1200 kHz SWITCHING FREQ-MAX, PQCC32 |
| 封裝： | GREEN, PLASTIC, QFN-32 |
| 文件頁數： | 8/40頁 |
| 文件大小： | 940K |
| 代理商： | TPS40131RHBTG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
www.ti.com
APPLICATION INFORMATION
LAYOUT CONSIDERATIONS
Power Stage
Device Peripheral
SLVS635 – FEBRUARY 2007
A synchronous BUCK power stage has two primary current loops. One is the input current loop that carries high
AC discontinuous current . The other is the output current loop that carries high DC continuous current.
The input current loop includes the input capacitors, the main switching MOSFET, the inductor, the output
capacitors and the ground path back to the input capacitors. To keep this loop as small as possible, it is
generally good practice to place some ceramic capacitance directly between the drain of the main switching
MOSFET and the source of the synchronous rectifier (SR) through a power ground plane directly under the
MOSFETs.
The output current loop includes the SR MOSFET, the inductor, the output capacitors, and the ground return
between the output capacitors and the source of the SR MOSFET. As with the input current loop, the ground
return between the output capacitor ground and the source of the SR MOSFET should be routed under the
inductor and SR MOSFET to minimize the power loop area.
The SW node area should be as small as possible to reduce the parasitic capacitance and minimize the radiated
emissions. The gate drive loop impedance (HDRV-gate-source-SW and LDRV-gate-source- GND) should be
kept to as low as possible. The HDRV and LDRV connections should widen to 20 mils as soon as possible out
from the device's pin.
The TPS40131 provides separate signal ground (GND) and power ground (PGND) pins. It is required to
separate properly the circuit grounds. The return path for the pins associated with the power stage should be
through PGND. The other pins especially for those sensitive pins such as FB, RT and ILIM should be through
the low noise GND. The GND and PGND plane are suggested to be connected at the output capacitor with
single 20 mil trace.
A minimum 0.1-
μF ceramic capacitor must be placed as close to the VDD pin and GND as possible with at least
15-mil wide trace from the bypass capacitor to the GND. A 1-
μF ceramic capacitor should be placed as close to
VIN5 pin and GND as possible.
BP5 is the filtered input from the VIN5 pin. A 10
resistor should be connected between VIN5 and BP5 and a
1-
μF ceramic capacitor should be connected from BP5 to GND. Both components should be as close to BP5 pin
as possible.
When DCR sensing method is applied, the sensing resistor is placed close to the SW node. It is connected to
the inductor with Kelvin connection. The sensing traces from the power stage to the device should be away from
the switching components. The sensing capacitor should be placed very close to the CS and CSRT pins. The
frequency setting resistor should be placed as close to RT pin and GND as possible.
The VOUT and GSNS pins should be directly connected to the point of load where the voltage regulation is
required. A parallel pair of 10-mil traces connects the regulated voltage back to the chip. They should be away
from the switching components. The PowerPAD should be electrically connected to GND. Figure 7 shows the
device peripheral schematic and Figure 8 shows the suggested layout.
16
相關PDF資料 |
PDF描述 |
|---|---|
| TPS40131RHBR | SWITCHING CONTROLLER, 1200 kHz SWITCHING FREQ-MAX, PQCC32 |
| TPS40132RHBR | 40 A SWITCHING CONTROLLER, 1200 kHz SWITCHING FREQ-MAX, PQCC32 |
| TPS40197RGYR | SWITCHING CONTROLLER, 520 kHz SWITCHING FREQ-MAX, PQCC16 |
| TPS40200MDREPG4 | SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS40211DRCTG4 | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS40132 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:TWO-PHASE, SYNCHRONOUS BUCK CONTROLLER WITH INTEGRATED MOSFET DRIVERS |
| TPS40132RHBR | 功能描述:DC/DC 開關控制器 2Ch Multiphase Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40132RHBRG4 | 功能描述:DC/DC 開關控制器 2Ch Multiphase Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40132RHBT | 功能描述:DC/DC 開關控制器 2Ch Multiphase Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40132RHBTG4 | 功能描述:DC/DC 開關控制器 2Ch Multiphase Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。