- 您現在的位置：買賣IC網 > PDF目錄98281 > TPS40197RGYR (TEXAS INSTRUMENTS INC) SWITCHING CONTROLLER, 520 kHz SWITCHING FREQ-MAX, PQCC16 PDF資料下載
參數資料
| 型號： | TPS40197RGYR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 520 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封裝： | PLASTIC, MO-241BB, VQFN-16 |
| 文件頁數： | 7/30頁 |
| 文件大?。?/td> | 931K |
| 代理商： | TPS40197RGYR |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
ILIMH(min)
OUT(max)
DS(on)max
V
I
R
=
(
)
REF
TR
REF
VID TR
I
T
C
V
-
=
TI Information — Selective Disclosure
www.ti.com
SLUS886 – NOVEMBER 2008
Note that due to blanking time considerations, overcurrent threshold accuracy may fall off for duty cycle greater
than 75% because the overcurrent comparator has only a very short time to sample the SW pin voltage under
these conditions and may not have time to respond to voltages very near the threshold.
The short-circuit protection threshold for the high-side MOSFET is fixed at 550 mV typical, 400 mV minimum.
This threshold is in place to provide a maximum current output using pulse-by-pulse current limit in the case of a
fault. The pulse terminates when the voltage drop across the high-side FET exceeds the short-circuit threshold.
The maximum amount of current that can be guaranteed to be sourced from a converter can be found by
where
IOUT(max) is the maximum current that the converter is guaranteed to source
VILIMH(min) is the short-circuit threshold for the high-side MOSFET (400 mV)
RDS(on)max is the maximum resistance of the high-side MOSFET
(4)
If the required current from the converter is greater than the calculated IOUT(max), a lower resistance high-side
MOSFET must be chosen. Both the high-side and low-side thresholds use temperature compensation to
approximate the change in resistance for a typical power MOSFET. This helps counteract shifts in overcurrent
thresholds as temperature increases. For this to be effective, the MOSFETs and the device must be well coupled
thermally.
Voltage Reference and Dynamic VID
To provide optimized voltage for Smart-Reflex DSP cores, the TPS40197 is designed to monitor the VID code
at all times once soft-start is complete, and actively adjusts its output voltage if the VID code should change
during normal operation. A digital-to-analog converter (DAC) generates a reference voltage based on the state of
logical signals at pins VID0 through VID3. The DAC decodes the 4-bit logic signal into one of the discrete
voltages shown in Table 2. The default setting for the output is 1.2 V (VID code 1111). The output voltage is
1.2 V during initial start or restart after cycling the input, toggling EN pin or recovering from a short circuit at the
output.
To ensure that no erroneous output voltage is produced, the TPS40197 VID inputs have internal anti-skew circuit
with approximately 550 ns of filtering time. Each VID input is pulled up to an internal 1.68-V source with 80-mA
pull-up current for use with open-drain outputs.
The output voltage can be programmed from 0.9 V to 1.2 V in 20 mV steps. Smooth upward and downward core
voltage transition can be achieved by programming the transition rate with an external capacitor connected from
REF pin to GND. The required capacitance can be calculated using Equation 5.
where
VVID-TR is the total voltage transition through VID
IREF is the internal reference source/sink current
TTR is the intended total VID voltage transition time
(5)
CREF must be limited to a maximum of 1.5 mF to avoid interfering with the soft-start. A capacitor (CREF) with a
minimum capacitance of 100-nF is also recommended.
Copyright 2008, Texas Instruments Incorporated
15
Product Folder Link(s): TPS40197
相關PDF資料 |
PDF描述 |
|---|---|
| TPS40200MDREPG4 | SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS40211DRCTG4 | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS40210DGQG4 | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS40304ADRCT | SWITCHING CONTROLLER, PQCC10 |
| TPS40304ADRCR | SWITCHING CONTROLLER, PQCC10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS40197RGYT | 功能描述:DC/DC 開關控制器 4.5-14V Inp Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40-20 | 制造商:TOTAL-POWER 制造商全稱:TOTAL-POWER 功能描述:40 WATT OPEN - FRAME SWITCHING POWER SUPPLY |
| TPS40200 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:WIDE INPUT RANGE NON-SYNCHRONOUS VOLTAGE MODE CONTROLLER |
| TPS40200_08 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:WIDE INPUT RANGE NON-SYNCHRONOUS VOLTAGE MODE CONTROLLER |
| TPS40200_081 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:WIDE INPUT RANGE NON-SYNCHRONOUS VOLTAGE MODE CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。