- 您現在的位置：買賣IC網 > PDF目錄382678 > TPS5103IDBR SMPS Controller PDF資料下載
參數資料
| 型號： | TPS5103IDBR |
| 英文描述： | SMPS Controller |
| 中文描述： | 開關電源控制器 |
| 文件頁數： | 4/31頁 |
| 文件大?。?/td> | 1083K |
| 代理商： | TPS5103IDBR |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
TPS5102
DUAL, HIGH-EFFICIENCY CONTROLLER FOR NOTEBOOK PC POWER
SLVS239 - SEPTEMBER 1999
4
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
detailed description
Vref (1.185 V)
The reference voltage is used to set the output voltage and the overvoltage protection (COMP).
Vref5 (5 V)
The internal linear voltage regulator is used for the high-side driver bootstrap voltage. Since the input voltage
range is from 4.5 V to 25 V, this feature offers a fixed voltage for the bootstrap voltage greatly simplifying the
drive design. It is also used for powering the low side driver. The tolerance is 6%.
5-V Switch
If the internal 5 V switch senses a 5-V input from REG5V_IN pin, the internal 5-V linear regulator will be
disconnected from the MOSFET drivers. The external 5 V will be used for both the low-side driver and the high
side bootstrap, thus increasing the efficiency.
PWM/SKIP
This pin is used to change between PWM and Skip mode. If the pin is lower than 0.5-V, the IC is in regular PWM
mode; if a minimum 2-V is applied to this pin, the IC works in Skip mode. In light load condition (<0.2 A), the
skip mode gives a short pulse to the low-side FET instead of a full pulse. By this control, switching frequency
is lowered, reducing switching loss; also the output capacitor energy discharging through the output inductor
and the low-side FET is prevented. Therefore, the IC can achieve high efficiency at light load conditions
(< 0.2 A).
err-amp
Each channel has its own error amplifier to regulate the output voltage of the synchronous-buck converter. It
is used in the PWM mode for the high output current condition (>0.2A). Voltage mode control is applied.
skip comparator
In Skip mode,
each channel has its own hysteretic comparator to regulate the output voltage of the
synchronous-buck converter. The hysteresis is set internally and typically at 8.5 mV. The delay from the
comparator input to the driver output is typically 1.2
μ
s.
low-side driver
The low-side driver is designed to drive low-Rds(on) n-channel MOSFETs. The maximum drive voltage is 5 V
from Vref5. The current rating of the driver is typically 1 A, source and sink.
high-side driver
The high side driver is designed to drive low-Rds(on) n-channel MOSFETs. The current rating of the driver is
1 A, source and sink. When configured as a floating driver, the bias voltage to the driver is developed from Vref5,
limiting the maximum drive voltage between OUT_u and LL to 5 V. The maximum voltage that can be applied
between LHx and OUTGND is 30 V.
deadtime control
Deadtime prevents shoot–through current from flowing through the main power FETs during switching
transitions by actively controlling the turn-on time of the MOSFETs drivers. The typical deadtime from
low-side-driver-off to high-side-driver-on is 70 ns, and 85 ns from high-side-driver-off to low-side-driver-on.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| TPS5210DWR | Voltage-Mode SMPS Controller |
| TPS5210PWPR | Voltage-Mode SMPS Controller |
| TPS5211PWPR | Analog IC |
| TPS524 | PHOTOVOLTAIC CELL FOR THERMOPILE DETECTION |
| TPS5300DAP | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS5103IDBRG4 | 功能描述:DC/DC 開關控制器 Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS5110 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-A SINK/ SOURCE DDR TERMINATION REGULATOR |
| TPS51100 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-A SINK/SOURCE DDR TERMINATION REGULATOR |
| TPS51100_07 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-A SINK/SOURCE DDR TERMINATION REGULATOR |
| TPS51100DGQ | 功能描述:低壓差穩壓器 - LDO 3A Source/Sink DDR Terminator Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。