- 您現在的位置：買賣IC網 > PDF目錄98283 > TPS54980PWP (TEXAS INSTRUMENTS INC) 16 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 PDF資料下載
參數資料
| 型號： | TPS54980PWP |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 16 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | GREEN, PLASTIC, HTSSOP-28 |
| 文件頁數： | 21/21頁 |
| 文件大小： | 568K |
| 代理商： | TPS54980PWP |
TPS54980
SLVS452A FEBRUARY 2003 REVISED FEBRUARY 2005
www.ti.com
9
PCB LAYOUT
Figure 10 shows a generalized PCB layout guide for the
TPS54980. The PVIN pins should be connected together
on the printed circuit board (PCB) and bypassed with a low
ESR ceramic bypass capacitor. Care should be taken to
minimize the loop area formed by the bypass capacitor
connections, the VIN pins, and the TPS54980 ground
pins. The minimum recommended bypass capacitance is
10
F ceramic with a X5R or X7R dielectric and the
optimum placement is closest to the VIN pins and the
PGND pins.
The TPS54980 has two internal grounds (analog and
power). The analog ground ties to all of the noise sensitive
signals, while the power ground ties to the noisier power
signals. Noise injected between the two grounds can
degrade the performance of the TPS54980, particularly at
higher output currents. Ground noise on an analog ground
plane can also cause problems with some of the control
and bias signals. For these reasons, separate analog and
power ground traces are recommended. There should be
an area of ground on the top layer directly under the IC,
with an exposed area for connection to the PowerPAD.
Use vias to connect this ground area to any internal ground
planes. Use additional vias at the ground side of the input
and output filter capacitors as well. The AGND and PGND
pins should be tied to the PCB ground by connecting them
to the ground area under the device as shown. The only
components that should tie directly to the power ground
plane are the input capacitors, the output capacitors, the
input voltage decoupling capacitor, and the PGND pins of
the TPS54980. Use a separate wide trace for the analog
ground signal path. This analog ground should be used for
the voltage set point divider, timing resistor RT, and bias
capacitor grounds. Connect this trace directly to AGND
(Pin 1).
The PH pins should be tied together and routed to the
output inductor. Since the PH connection is the switching
node, the inductor should be located very close to the PH
pins and the area of the PCB conductor minimized to
prevent excessive capacitive coupling.
Connect the boot capacitor between the phase node and
the BOOT pin as shown. Keep the boot capacitor close to
the IC and minimize the conductor trace lengths.
Connect the output filter capacitor(s) as shown between
the VOUT trace and PGND. It is important to keep the loop
formed by the PH pins, Lout, Cout, and PGND as small as
practical.
Place the compensation components from the VOUT trace
to the VSENSE and COMP pins. Do not place these
components too close to the PH trace. Due to the size of
the IC package and the device pinout, the components will
have to be routed somewhat close, but maintain as much
separation as possible while still keeping the layout
compact.
Connect the bias capacitor from the VBIAS pin to analog
ground using the isolated analog ground trace. If an RT
resistor is used, connect it to this trace as well.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS55383PWPRG4 | 7 A DUAL SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS5602IDBR | 3 A DUAL SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO30 |
| TPS5602IDBTRG4 | 3 A DUAL SWITCHING CONTROLLER, 202.4 kHz SWITCHING FREQ-MAX, PDSO30 |
| TPS5602IDBTR | 3 A DUAL SWITCHING CONTROLLER, 202.4 kHz SWITCHING FREQ-MAX, PDSO30 |
| TPS561000PWP | 1.4 A SWITCHING CONTROLLER, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS54980PWPG4 | 功能描述:直流/直流開關調節器 3.3V Input Synch Buck Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS54980PWPR | 功能描述:直流/直流開關調節器 3.3V Inp Sync Buck Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS54980PWPRG4 | 功能描述:直流/直流開關調節器 3.3V Inp Sync Buck Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS549A20EVM-737 | 功能描述:EVALUATION MODULE 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1 |
| TPS549A20RVET | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.6V 1 Output 15A 28-VFQFN Exposed Pad 制造商:texas instruments 系列:SWIFT?，D-CAP3?，Eco-Mode? 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:1.5V 電壓 - 輸入（最大值）:20V 電壓 - 輸出（最小值/固定）:0.6V 電壓 - 輸出（最大值）:5.5V 電流 - 輸出:15A 頻率 - 開關:可選 同步整流器:是 工作溫度:-40°C ~ 125°C（TA） 安裝類型:表面貼裝 封裝/外殼:28-VFQFN 裸露焊盤 供應商器件封裝:28-VQFN（4.5x3.5） 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。