- 您現在的位置：買賣IC網 > PDF目錄98283 > TPS55383PWPRG4 (TEXAS INSTRUMENTS INC) 7 A DUAL SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
參數資料
| 型號： | TPS55383PWPRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 7 A DUAL SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | PLASTIC, HTSSOP-26 |
| 文件頁數： | 22/45頁 |
| 文件大小： | 1318K |
| 代理商： | TPS55383PWPRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
PCB Layout Guidelines
www.ti.com ......................................................................................................................................................................................... SLUS818 – SEPTEMBER 2008
The layout guidelines presented here are illustrated in the PCB layout examples given in Figure 31 and
Power pad must be connected to low current ground with available surface copper to dissipate heat.
Recommend extending ground land beyond device package area.
Connect the GND pin to the PowerPAD through a 10-mil (.010 in, or 0.0254 mm) wide trace.
Place the ceramic input capacitors close to PVDD1 and PVDD2; Connect ceramic input capacitor ground to
PowerPad with min 50mil wide trace.
Maintain tight loop of wide traces from SW1 or SW2 through switch node, inductor, output capacitor and
rectifier diode. Avoid using vias in this loop.
Use wide ground connection from input capacitor to rectifier diode as close to power path as possible.
Recommend directly under diode and switch node.
Locate bootstrap capacitor close to BOOT pin to minimize gate drive loop.
Locate feedback and compensation components over GND and away from switch node and rectifier diode to
input capacitor ground connection.
Locate snubber components close to rectifier diode with minimize loop area.
Locate BP bypass capacitor very close to device. Recommend minimal loop area.
Locate output ceramic capacitor close to inductor output terminal between inductor and electrolytic capacitors
if used.
Figure 31. Top Layer Copper Layout and Component
Figure 32. Bottom Layer Copper Layout
Placement
Copyright 2008, Texas Instruments Incorporated
29
相關PDF資料 |
PDF描述 |
|---|---|
| TPS5602IDBR | 3 A DUAL SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO30 |
| TPS5602IDBTRG4 | 3 A DUAL SWITCHING CONTROLLER, 202.4 kHz SWITCHING FREQ-MAX, PDSO30 |
| TPS5602IDBTR | 3 A DUAL SWITCHING CONTROLLER, 202.4 kHz SWITCHING FREQ-MAX, PDSO30 |
| TPS561000PWP | 1.4 A SWITCHING CONTROLLER, PDSO28 |
| TPS56100PWPR | 1.4 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS55386EVM-363 | 功能描述:電源管理IC開發工具 TPS55386EVM-363 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS55386PWP | 功能描述:直流/直流開關調節器 3A Dual Non-Synch Buck Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS55386PWPG4 | 功能描述:直流/直流開關調節器 3A,Dual Non-Synch Buck Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS55386PWPR | 功能描述:直流/直流開關調節器 3A Dual Non-Synch Buck Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS55386PWPRG4 | 功能描述:直流/直流開關調節器 3A,Dual Non-Synch Buck Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。