- 您現在的位置：買賣IC網 > PDF目錄98283 > TPS61045DRBR (TEXAS INSTRUMENTS INC) 0.45 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | TPS61045DRBR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.45 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 3 X 3 MM, GREEN, PLASTIC, SON-8 |
| 文件頁數： | 5/21頁 |
| 文件大小： | 582K |
| 代理商： | TPS61045DRBR |
www.ti.com
SLVS440B – JANUARY 2003 – REVISED MARCH 2009
INPUT CAPACITOR SELECTION
The input capacitor (C1) filters the high frequency noise to the control circuit and must be directly connected to
the input pin (VIN) of the device. The capacitor (C2) connected to the L pin of the device is the input capacitor for
the power stage.
The main purpose of the capacitor (C2), that is connected directly to the L pin, is to smooth the inductor current.
A larger capacitor reduces the inductor ripple current present at the L pin. The smaller the ripple current at the L
pin, the higher the efficiency of the converter. If a sufficiently large capacitor is used, the input switch must carry
only the dc current, filtered by the capacitor (C2), and not the high switching currents of the converter. A 4.7 mF
or 10-mF ceramic capacitor (C2) is sufficient for most applications. For better filtering, this value can be increased
without limit. See Table 4 and the TYPICAL APPLICATIONS for input capacitor recommendations.
Table 4. Possible Input and Output Capacitor Selection
CAPACITOR
VOLTAGE RATING
COMPONENT SUPPLIER
COMMENTS
4.7 F/X5R/0805
6.3 V
Tayo Yuden JMK212BY475MG
CI/CO
10 mF/X5R/0805
6.3 V
Tayo Yuden JMK212BJ106MG
CI/CO
1 mF/X7R/1206
25 V
Tayo Yuden TMK316BJ105KL
CO
1 mF/X7R/1206
35 V
Tayo Yuden GMK316BJ105KL
CO
4.7 mF/X5R/1210
25 V
Tayo Yuden TMK325BJ475MG
CO
DIODE SELECTION
To achieve high efficiency a Schottky diode must be used. The current rating of the diode must meet the peak
current rating of the converter as it is calculated in the peak current control section. Use the maximum value for
I(LIM) (450mA) for this calculation. See Table 5 and the TYPICAL APPLICATIONS for the selection of the
Schottky diode.
Table 5. Possible Schottky Diode Selection
COMPONENT SUPPLIER
REVERSE VOLTAGE
ON Semiconductor MBR0530
30 V
ON Semiconductor MBR0520
20 V
ON Semiconductor MBRM120L
20 V
Toshiba CRS02
30 V
Zetex ZHZS400
40 V
LAYOUT CONSIDERATIONS
As for all switching power supplies the layout is an important step in the design, especially at high peak currents
and switching frequencies. If the layout is not carefully implemented, the regulator can show noise problems and
duty cycle jitter.
The inductor and diode must be placed as close as possible to the switch pin (SW) to minimize noise coupling
into other circuits. Since the feedback pin and network is a high impedance circuit, the feedback network must be
routed away from the inductor. Also the input capacitor must be placed as close as possible to the input pin for
good input-voltage filtering. If space is critical and the described can not be followed completely, the close
placement of the diode to the switch pin (SW) must be given the highest priority.
THERMAL CONSIDERATIONS
The TPS61045 is available in a thermally enhanced QFN package. The package includes a thermal pad,
improving the thermal capabilities of the package. See QFN/SON PCB attachment application note (SLUA271).
The thermal resistance junction to ambient (RΘJA) of the QFN package depends on the PCB layout. By using
thermal vias and wide PCB, traces improve thermal resistance (RΘJA). Under normal operation conditions no
PCB vias are required for the thermal pad. However, the thermal pad must be soldered to the PCB.
Copyright 2003–2009, Texas Instruments Incorporated
13
Product Folder Link(s): TPS61045
相關PDF資料 |
PDF描述 |
|---|---|
| TPS61080DRCR | 1 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61081DRCTG4 | 1.3 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61080DRCTG4 | 0.5 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61093DSK | 1.5 A SWITCHING REGULATOR, 1400 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61122PWRG4 | 1.6 A BATTERY CHARGE CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS61045DRBRG4 | 功能描述:LED顯示驅動器 28-V 85% Eff Boost Converter RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| TPS61045DRBT | 功能描述:LED顯示驅動器 28-V 85% Eff Boost Converter RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| TPS61045DRBTG4 | 功能描述:LED照明驅動器 28-V 85% Eff Boost Converter RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| TPS61045EVM-231 | 功能描述:電源管理IC開發工具 TPS61045-231 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS61046EVM-682 | 功能描述:TPS61046 - DC/DC, Step Up 2, Non-Isolated Outputs Evaluation Board 制造商:texas instruments 系列:- 零件狀態:有效 主要用途:DC/DC，步升 輸出和類型:2，非隔離 功率 - 輸出:- 電壓 - 輸出:12V，5 V ~ 28 V 電流 - 輸出:100mA，20mA 電壓 - 輸入:1.8 V ~ 5.5 V 穩壓器拓撲:升壓 頻率 - 開關:1MHz 板類型:完全填充 所含物品:板 使用的 IC/零件:TPS61046 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。