- 您現在的位置：買賣IC網 > PDF目錄98285 > TPS62672YFD (TEXAS INSTRUMENTS INC) 1.15 A SWITCHING REGULATOR, 6600 kHz SWITCHING FREQ-MAX, PBGA6 PDF資料下載
參數資料
| 型號： | TPS62672YFD |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.15 A SWITCHING REGULATOR, 6600 kHz SWITCHING FREQ-MAX, PBGA6 |
| 封裝： | 0.40 MM HEIGHT, DSBGA-6 |
| 文件頁數： | 17/34頁 |
| 文件大小： | 1129K |
| 代理商： | TPS62672YFD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
SLVS952C
– APRIL 2010 – REVISED APRIL 2011
OUTPUT CAPACITOR SELECTION
The advanced fast-response voltage mode control scheme of the TPS6267x allows the use of tiny ceramic
capacitors. Ceramic capacitors with low ESR values have the lowest output voltage ripple and are
recommended. For best performance, the device should be operated with a minimum effective output
capacitance of 0.8
μF. The output capacitor requires either an X7R or X5R dielectric. Y5V and Z5U dielectric
capacitors, aside from their wide variation in capacitance over temperature, become resistive at high frequencies.
At nominal load current, the device operates in PWM mode and the overall output voltage ripple is the sum of the
voltage step caused by the output capacitor ESL and the ripple current flowing through the output capacitor
impedance.
At light loads, the output capacitor limits the output ripple voltage and provides holdup during large load
transitions. A 2.2
μF or 4.7μF ceramic capacitor typically provides sufficient bulk capacitance to stabilize the
output during large load transitions. The typical output voltage ripple is 1% of the nominal output voltage VO.
For best operation (i.e. optimum efficiency over the entire load current range, proper PFM/PWM auto transition),
the TPS6267x requires a minimum output ripple voltage in PFM mode. The typical output voltage ripple is ca. 1%
of the nominal output voltage VO. The PFM pulses are time controlled resulting in a PFM output voltage ripple
and PFM frequency that depends (first order) on the capacitance seen at the converter's output.
INPUT CAPACITOR SELECTION
Because of the nature of the buck converter having a pulsating input current, a low ESR input capacitor is
required to prevent large voltage transients that can cause misbehavior of the device or interferences with other
circuits in the system. For most applications, a 1 or 2.2-
μF capacitor is sufficient. If the application exhibits a
noisy or erratic switching frequency, the remedy will probably be found by experimenting with the value of the
input capacitor.
Take care when using only ceramic input capacitors. When a ceramic capacitor is used at the input and the
power is being supplied through long wires, such as from a wall adapter, a load step at the output can induce
ringing at the VIN pin. This ringing can couple to the output and be mistaken as loop instability or could even
damage the part. Additional "bulk" capacitance (electrolytic or tantalum) should in this circumstance be placed
between CI and the power source lead to reduce ringing than can occur between the inductance of the power
source leads and CI.
CHECKING LOOP STABILITY
The first step of circuit and stability evaluation is to look from a steady-state perspective at the following signals:
Switching node, SW
Inductor current, IL
Output ripple voltage, VO(AC)
These are the basic signals that need to be measured when evaluating a switching converter. When the
switching waveform shows large duty cycle jitter or the output voltage or inductor current shows oscillations, the
regulation loop may be unstable. This is often a result of board layout and/or L-C combination.
As a next step in the evaluation of the regulation loop, the load transient response is tested. The time between
the application of the load transient and the turn on of the P-channel MOSFET, the output capacitor must supply
all of the current required by the load. VO immediately shifts by an amount equal to ΔI(LOAD) x ESR, where ESR
is the effective series resistance of CO. ΔI(LOAD) begins to charge or discharge CO generating a feedback error
signal used by the regulator to return VO to its steady-state value. The results are most easily interpreted when
the device operates in PWM mode.
During this recovery time, VO can be monitored for settling time, overshoot or ringing that helps judge the
converter
’s stability. Without any ringing, the loop has usually more than 45° of phase margin.
Because the damping factor of the circuitry is directly related to several resistive parameters (e.g., MOSFET
rDS(on)) that are temperature dependant, the loop stability analysis has to be done over the input voltage range,
load current range, and temperature range.
24
Copyright
2010–2011, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS62676YFDR | SWITCHING REGULATOR, PBGA6 |
| TPS62677YFDR | SWITCHING REGULATOR, PBGA6 |
| TPS62677YFDT | SWITCHING REGULATOR, PBGA6 |
| TPS62690YFFR | 0.5 A SWITCHING REGULATOR, 4400 kHz SWITCHING FREQ-MAX, BGA6 |
| TPS62691YFFT | 0.6 A SWITCHING REGULATOR, 4400 kHz SWITCHING FREQ-MAX, BGA6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS62674YFDR | 功能描述:直流/直流開關轉換器 500mA,6MHz Hh-Eff Step-Down Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS62674YFDT | 功能描述:直流/直流開關轉換器 500mA,6MHz Hh-Eff Step-Down Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS626751YFDR | 功能描述:Buck Switching Regulator IC Positive Fixed 1.2V 1 Output 650mA 6-XFBGA, DSBGA 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:固定 輸出數:1 電壓 - 輸入（最小值）:2.3V 電壓 - 輸入（最大值）:4.8V 電壓 - 輸出（最小值/固定）:1.2V 電壓 - 輸出（最大值）:- 電流 - 輸出:650mA 頻率 - 開關:6MHz 同步整流器:是 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:6-XFBGA，DSBGA 供應商器件封裝:6-DSBGA 標準包裝:1 |
| TPS62675YFDR | 功能描述:直流/直流開關轉換器 500mA,6MHz Hi-Eff Step-Down Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS62675YFDT | 功能描述:直流/直流開關轉換器 500mA,6MHz Hi-Eff Step-Down Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。