- 您現在的位置：買賣IC網 > PDF目錄98285 > TPS62691YFFT (TEXAS INSTRUMENTS INC) 0.6 A SWITCHING REGULATOR, 4400 kHz SWITCHING FREQ-MAX, BGA6 PDF資料下載
參數資料
| 型號： | TPS62691YFFT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.6 A SWITCHING REGULATOR, 4400 kHz SWITCHING FREQ-MAX, BGA6 |
| 封裝： | DSBGA-6 |
| 文件頁數： | 14/27頁 |
| 文件大小： | 870K |
| 代理商： | TPS62691YFFT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
MODE
ENABLE
C
I
L
V
IN
C
O
V
OUT
GND
J(MAX)
A
D(MAX)
JA
T
- T
105 C - 85 C
P
=
= 160mW
R
125 C/W
q
°
SLVS965
– MARCH 2011
LAYOUT CONSIDERATIONS
As for all switching power supplies, the layout is an important step in the design. High-speed operation of the
TPS6269x devices demand careful attention to PCB layout. Care must be taken in board layout to get the
specified performance. If the layout is not carefully done, the regulator could show poor line and/or load
regulation, stability and switching frequency issues as well as EMI problems. It is critical to provide a low
inductance, impedance ground path. Therefore, use wide and short traces for the main current paths.
The input capacitor should be placed as close as possible to the IC pins as well as the inductor and output
capacitor. In order to get an optimum ESL step, the output voltage feedback point (FB) should be taken in the
output capacitor path, approximately 1mm away for it. The feed-back line should be routed away from noisy
components and traces (e.g. SW line).
Figure 36. Suggested Layout (Top)
THERMAL INFORMATION
Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires
special attention to power dissipation. Many system-dependant issues such as thermal coupling, airflow, added
heat sinks, and convection surfaces, and the presence of other heat-generating components, affect the
power-dissipation limits of a given component.
Three basic approaches for enhancing thermal performance are listed below:
Improving the power dissipation capability of the PCB design
Improving the thermal coupling of the component to the PCB
Introducing airflow into the system
The maximum recommended junction temperature (TJ) of the TPS6269x devices is 105°C. The thermal
resistance of the 6-pin CSP package (YFF-6) is RθJA = 125°C/W. Regulator operation is specified to a maximum
steady-state ambient temperature TA of 85°C. Therefore, the maximum power dissipation is about 160 mW.
(3)
2011, Texas Instruments Incorporated
21
相關PDF資料 |
PDF描述 |
|---|---|
| TPS62751DSKR | 1.8 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS63000IDRCRQ1 | 2.1 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS65011RGZT | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC48 |
| TPS65023QRHARQ1 | POWER SUPPLY SUPPORT CKT, PQCC40 |
| TPS65040ZQER | 8-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA71 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS62692EVM-076 | 制造商:Texas Instruments 功能描述:TPS62692EVM-076 EVALUATION MODULE |
| TPS62692YFDR | 制造商:Texas Instruments 功能描述: |
| TPS62693YFDR | 功能描述:直流/直流開關轉換器 800-mA 3-MHz Hi-Eff SD Cnvtr RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS62693YFDT | 功能描述:直流/直流開關轉換器 800-mA 3-MHz Hi-Eff SD Cnvtr RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS62698YFDR | 功能描述:直流/直流開關轉換器 800mA 3MHz Hi-Eff SD Cnvtr RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。