- 您現在的位置：買賣IC網 > PDF目錄98285 > TPS62751DSKR (TEXAS INSTRUMENTS INC) 1.8 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 PDF資料下載
參數資料
| 型號： | TPS62751DSKR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.8 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | 2.50 X 2.50 MM, GREEN, PLASTIC, SON-10 |
| 文件頁數： | 10/30頁 |
| 文件大小： | 1733K |
| 代理商： | TPS62751DSKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
L
Vout
1
Vin
I
= Vout
L
-
D
L
Lmax
outmax
I
= I
+
2
D
SLVS955A – JULY 2009 – REVISED SEPTEMBER 2009 ................................................................................................................................................. www.ti.com
INDUCTOR SELECTION
The inductor value has a direct effect on the ripple current. The selected inductor has to be rated for its dc
resistance and saturation current. The inductor ripple current (
ΔIL) decreases with higher inductance and
increases with higher VIN or VOUT.
The inductor selection has also impact on the output voltage ripple in PFM mode. Higher inductor values will lead
to lower output voltage ripple and higher PFM frequency, lower inductor values will lead to a higher output
voltage ripple but lower PFM frequency.
Equation 2 calculates the maximum inductor current under static load conditions. The saturation current of the
inductor should be rated higher than the maximum inductor current as calculated with Equation 3. This is
recommended because during heavy load transient the inductor current will rise above the calculated value.
(2)
(3)
With:
f = Switching Frequency (2.25MHz typical)
L = Inductor Value
ΔIL= Peak to Peak inductor ripple current
ILmax = Maximum Inductor current
A more conservative approach is to select the inductor current rating just for the maximum switch current of the
corresponding converter. Accepting larger values of ripple current allows the use of low inductance values, but
results in higher output voltage ripple, greater core losses, and lower output current capability. The device has
been optimized to operate with inductance values between 1.0
μH and 4.7μH. It is recommended that inductance
values of at least 1.0
μH is used, even if Equations 2 and 3 yield something lower.
The total losses of the coil have a strong impact on the efficiency of the DC/DC conversion and consist of both
the losses in the dc resistance (R(DC)) and the following frequency-dependent components:
The losses in the core material (magnetic hysteresis loss, especially at high switching frequencies)
Additional losses in the conductor from the skin effect (current displacement at high frequencies)
Magnetic field losses of the neighboring windings (proximity effect)
Radiation losses
Table 3. List of Inductors
MANUFACTURER
INDUCTOR TYPE
DIMENSIONS [mm]
Coilcraft
LPS3015-222ML
3.0 x 3.0 x 1.5
TOKO
1127AS-2R2M
3.5 x 3.7 x 1.8
Murata
LQH32PN1R0N0
3.2 x 2.5 x 1.7
TOKO
DB3015 Series
3.2 x 3.2 x 1.5
INPUT CAPACITOR SELECTION
Because of the nature of the buck converter having a pulsating input current, a low ESR input capacitor is
required for best input voltage filtering and minimizing the interference with other circuits caused by high
input voltage spikes. For most applications a 4.7
μF to 10μF ceramic capacitor is recommended. The input
capacitor can be increased without any limit for better input voltage filtering.
Take care when using only small ceramic input capacitors. When a ceramic capacitor is used at the input
and the power is being supplied through long wires, such as from a wall adapter, a load step at the output or
VIN step on the input can induce ringing at the VIN pin. This ringing can couple to the output and be
mistaken as loop instability or could even damage the part by exceeding the maximum ratings.
18
Copyright 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPS62750, TPS62751
相關PDF資料 |
PDF描述 |
|---|---|
| TPS63000IDRCRQ1 | 2.1 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS65011RGZT | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC48 |
| TPS65023QRHARQ1 | POWER SUPPLY SUPPORT CKT, PQCC40 |
| TPS65040ZQER | 8-CHANNEL POWER SUPPLY MANAGEMENT CKT, PBGA71 |
| TPS650531IRGERQ1 | POWER SUPPLY SUPPORT CKT, PQCC24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS62751DSKT | 功能描述:直流/直流開關調節器 2.25MHz 92% Eff Step Down Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS62770EVM-734 | 功能描述:TPS62770 - DC/DC, Step Up or Down 2, Non-Isolated Outputs Evaluation Board 制造商:texas instruments 系列:- 零件狀態:有效 主要用途:DC/DC，步升/步降 輸出和類型:2，非隔離 功率 - 輸出:- 電壓 - 輸出:- 電流 - 輸出:- 電壓 - 輸入:2.5 V ~ 5.5 V 穩壓器拓撲:降壓-升壓 頻率 - 開關:- 板類型:完全填充 所含物品:板 使用的 IC/零件:TPS62770 標準包裝:1 |
| TPS62770YFPT | 功能描述:Buck, Boost Switching Regulator IC Positive Programmable 1V, 4.5V (12V) 2 Output 300mA, 30mA, 100mA, 200mA 16-XFBGA, DSBGA 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 功能:升壓，降壓 輸出配置:正 拓撲:降壓，升壓 輸出類型:可編程 輸出數:2 電壓 - 輸入（最小值）:2.5V 電壓 - 輸入（最大值）:5.5V 電壓 - 輸出（最小值/固定）:1V，4.5V（12V） 電壓 - 輸出（最大值）:3V，15V 電流 - 輸出:300mA，30mA，100mA，200mA 頻率 - 開關:1.05MHz 同步整流器:是 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:16-XFBGA，DSBGA 供應商器件封裝:16-DSBGA 標準包裝:1 |
| TPS63000DRCR | 功能描述:直流/直流開關調節器 96% Buck Boost Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS63000DRCRG4 | 功能描述:直流/直流開關調節器 96% Buck Boost Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。