欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TPS650732TRSLRQ1
廠商: TEXAS INSTRUMENTS INC
元件分類: 電源管理
英文描述: POWER SUPPLY SUPPORT CKT, PQCC48
封裝: 6 X 6 MM, 0.4 MM PITCH, GREEN, PLASTIC, QFN-48
文件頁數: 32/90頁
文件大小: 1375K
代理商: TPS650732TRSLRQ1
SLVSAP7 – JANUARY 2011
www.ti.com
Table 3. TSC Equations
MEASUREMENT
CHANNEL
EQUATION
X Plate resistance
AD_IN14
Rx = VTSREF/ [(VADC / 22k) × 150]
Y plate resistance
AD_IN14
Ry = VTSREF / [(VADC / 22k) × 150]
X position
AD_IN14
Xpos = Rx2 / (Rx1 + Rx2) = Rx2 / Rx
Rx2 = VADC x Rx/ VTSREF; Rx1 = Rx – Rx2
Xpos = ADRESULT / 1024
Y position
AD_IN14
Ypos = Ry2 / (Ry1 + Ry2) = Ry2 / Ry
Ry2 = VADC x Ry/ VTSREF; Ry1 = Ry – Ry2
Ypos = ADRESULT / 1024
Pressure
AD_IN14
Rc = R – Rx1//Rx2 – Ry1//Ry2
R = VTSREF/ [(VADC / 22k) × 150]
Rx1//Rx2 = Rx × Xpos × (1 – Xpos)
Ry1//Ry2 = Ry × Ypos × (1 – Ypos)
Performing Measurements Using the Touch Screen Controller
In order to take measurements with the touch screen controller, the ADC has to be enabled and configured for
use with the touch screen controller (TSC) first. In case the TSC is planned to be operated interrupt driven, the
TSC needs to be in TSC standby mode per default. Only in TSC standby mode an interrupt is generated based
on a touch of the screen. The TSC should therefore be in this mode until a touch is detected. Afterwards, the
TSC has to be configured for x-position measurement followed by y-position measurement. Now, the TSC can be
set to TSC standby again to wait for the next touch of the screen. For a non-interrupt driven sequence, see
TSCMODE. Register Address: 08h (page 50) in the Registers section. A typical interrupt driven sequence is
given below:
Set TSCMODE to 101 to set TSC to TSC standby, so an interrupt is generated when the screen is touched
Set Bit AD enable = 1 to provide power to the ADC
Set input select for the ADC in register ADCONFIG to 1110 (AD_IN14 selected)
In register INT, set MASK TSC = 1 to unmask the interrupt on a touch of the touch screen
Read Bit TSC INT as it will be set after the TSC has been configured. Reading clears the interrupt.
After a touch was detected, an interrupt is generated by INT pin going LOW
Read Bit TSC INT to clear the interrupt
Set TSCMODE to 000 to select x-position measurement
Start an ADC conversion by setting CONVERSION START =1; wait until END OF CONVERSION = 1
Read register ADRESULT_1 and AD_RESULT_2
Set TSCMODE to 001 to select y-position measurement
Start an ADC conversion by setting CONVERSION START =1; wait until END OF CONVERSION = 1
Read register ADRESULT_1 and AD_RESULT_2
Set TSCMODE to 101 to set TSC to TSC standby again
38
Copyright 2011, Texas Instruments Incorporated
相關PDF資料
PDF描述
TPS65110RGEG3 SWITCHED CAPACITOR REGULATOR, 520 kHz SWITCHING FREQ-MAX, PQCC24
TPS65130RGER 0.9 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24
TPS65130RGET 0.9 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24
TPS65131RGETG4 2.2 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24
TPS65130RGE 0.9 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24
相關代理商/技術參數
參數描述
TPS65073EVM-430 功能描述:電源管理IC開發工具 TPS65073 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS65073RSLR 功能描述:PMIC 解決方案 5Ch Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
TPS65073RSLT 功能描述:PMIC 解決方案 5Ch Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
TPS650830EVM-095 功能描述:TPS650830 - Power Management, Special Purpose: Mobiles Evaluation Board 制造商:texas instruments 系列:- 零件狀態:有效 主要用途:電源管理,專用型: 手機 嵌入式:- 使用的 IC/零件:TPS650830 主要屬性:- 輔助屬性:圖形用戶接口,I2C 接口 所含物品:板 標準包裝:1
TPS650830ZAJT 功能描述:- Converter, Mobile PCs Voltage Regulator IC 8 Output 168-NFBGA (7x7) 制造商:texas instruments 系列:- 包裝:剪切帶(CT) 零件狀態:有效 應用:轉換器,移動式個人電腦 電壓 - 輸入:5.4 V ~ 24 V 輸出數:8 電壓 - 輸出:多重 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:168-TFBGA 供應商器件封裝:168-NFBGA(7x7) 標準包裝:1
主站蜘蛛池模板: 焦作市| 通海县| 长武县| 祁东县| 抚远县| 安溪县| 同心县| 宁强县| 凌海市| 柘荣县| 阿巴嘎旗| 铁力市| 和顺县| 通河县| 平罗县| 富源县| 丹凤县| 东阿县| 晋中市| 灵寿县| 泗洪县| 黔东| 勃利县| 乐昌市| 沙河市| 宁津县| 绵竹市| 泰州市| 宁乡县| 武强县| 于田县| 邵武市| 揭阳市| 鹤壁市| 三明市| 临颍县| 吉林省| 通道| 安新县| 漠河县| 永康市|