欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TPS65130RGER
廠商: TEXAS INSTRUMENTS INC
元件分類: 穩壓器
英文描述: 0.9 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24
封裝: 4 X 4 MM, GREEN, PLASTIC, QFN-24
文件頁數: 19/34頁
文件大小: 785K
代理商: TPS65130RGER
www.ti.com
Stabilizing the Control Loop
C9 +
6.8 ms
R1
(11)
C10 +
7.5 ms
R3
(12)
Layout Considerations
THERMAL INFORMATION
P
DMAX +
T
JMAX *
T
A
R
qJA
(13)
TPS65130, TPS65131
SLVS493B – MARCH 2004 – REVISED SEPTEMBER 2004
Feedback Divider
To speed up the control loop, feedforward capacitors are recommended in the feedback divider, parallel to R1
(boost converter) and R3 (inverting converter). Equation 11 shows how to calculate the appropriate value for the
boost converter, and Equation 12 for the inverting converter.
To avoid coupling noise into the control loop from the feedforward capacitors, the feedforward effect can be
bandwith-limited by adding a series resistor. Any value between 10 k
and 100 k is suitable. The higher the
resistance, the lower the noise coupled into the control loop system.
Compensation Capacitors
The control loops of both converters are completely compensated internally. The complex internal input voltage
output voltage, and input-current feedforward system has built-in error correction which requires external
capacitors. A 10-nF capacitor at CP of the boost converter and a 4.7-nF capacitor at CN of the inverting
converter is recommended.
As for all switching power supplies, the layout is an important step in the design, especially at high peak currents
and high switching frequencies. If the layout is not carefully done, the regulator could show stability problems as
well as EMI problems. Therefore, use wide and short traces for the main current paths and for the power ground
tracks. The input capacitors, output capacitors, the inductors, and the rectifying diodes should be placed as close
as possible to the IC to keep parasitic inductances low. Use a common ground node for power ground and a
different node for control grounds to minimize the effects of ground noise. Connect these ground nodes at any
place close to one of the ground pins of the IC.
The feedback dividers should be placed as close as possible to the control ground pin (boost converter) or the
VREF pin (inverting converter) of the IC. To lay out the control ground, it is recommended to use short traces as
well, seperated from the power ground traces. This avoids ground shift problems, which can occur due to
superimposition of power ground current and control ground current.
Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires
special attention to power dissipation. Many system-dependent issues, such as thermal coupling, airflow, added
heatsinks
and
convection
surfaces,
and
the
presence
of
heat-generating
components
affect
the
power-dissipation limits of a given component.
Three basic approaches for enhancing thermal performance follow.
Improving the power dissipation capability of the PCB design
Improving the thermal coupling of the component to the PCB
Introducing airflow to the system
The maximum recommended junction temperature (TJ) of the TPS65130/1 devices is 125°C. The thermal
resistance of the 24-pin QFN, 4x4-mm package (RGE) is RθJA = 37.8°C/W. Specified regulator operation is
ensured to a maximum ambient temperature TA of 85°C. Therefore, the maximum power dissipation is about
1058 mW. More power can be dissipated if the maximum ambient temperature of the application is lower.
26
相關PDF資料
PDF描述
TPS65130RGET 0.9 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24
TPS65131RGETG4 2.2 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24
TPS65130RGE 0.9 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24
TPS65131RGERG4 2.2 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PQCC24
TPS65136RTE 1.12 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PQCC16
相關代理商/技術參數
參數描述
TPS65130RGER 制造商:Texas Instruments 功能描述:IC DC-DC CONVERTER ((NW)) 制造商:Texas Instruments 功能描述:IC, DC-DC CONV, VQFN-24
TPS65130RGERG4 功能描述:DC/DC 開關控制器 Adj Dl Otp Switch Boost DC/DC RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS65130RGET 功能描述:DC/DC 開關控制器 Adj Dl Otp Switch Boost DC/DC RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS65130RGET 制造商:Texas Instruments 功能描述:IC CONV DC/DC POS/NEG 24-QFN
TPS65130RGETG4 功能描述:DC/DC 開關控制器 Adj Dl Otp Switch Boost DC/DC RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
主站蜘蛛池模板: 台中县| 甘谷县| 邢台县| 唐山市| 岑溪市| 和林格尔县| 黄平县| 临澧县| 德化县| 庄浪县| 杭锦旗| 南漳县| 普宁市| 永吉县| 偏关县| 富顺县| 浦北县| 湟源县| 隆化县| 繁昌县| 怀集县| 正蓝旗| 仁化县| 红河县| 府谷县| 黔南| 赤峰市| 隆林| 策勒县| 饶阳县| 张家川| 青海省| 巨野县| 凯里市| 新野县| 淄博市| 建平县| 迁安市| 新安县| 施秉县| 汉沽区|