欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TPS73218DCQT
廠商: Texas Instruments, Inc.
英文描述: MS/STANDARD CYLINDRICAL MIL-C-5015 SERIES 3102A SOLID SHELL BOX MOUNT RECEPTACLES, STRAIGHT BODY STYLE, SOLDER TERMINATION, 18 SHELL SIZE, 18-11 INSERT ARRANGEMENT, RECEPTACLE GENDER, 5 CONTACTS
中文描述: 無電容,NMOS管,250mA的低壓差穩壓器的反向電流保護
文件頁數: 14/18頁
文件大小: 427K
代理商: TPS73218DCQT
www.ti.com
dV dt
V
OUT
C
OUT
80k
(R
1
R
2
)
(5)
REVERSE CURRENT
The NMOS pass element of the TPS732xx provides
inherent protection against current flow from the
output of the regulator to the input when the gate of
the pass device is pulled low. To ensure that all
charge is removed from the gate of the pass element,
the enable pin must be driven low before the input
voltage is removed. If this is not done, the pass
element may be left on due to stored charge on the
gate.
POWER DISSIPATION
The ability to remove heat from the die is different for
each package type, presenting different consider-
ations in the PCB layout. The PCB area around the
device that is free of other components moves the
heat from the device to the ambient air. Performance
data for JEDEC low- and high-K boards are shown in
the Power Dissipation Ratings table. Using heavier
copper will increase the effectiveness in removing
heat
from
the
device.
through-holes to heat-dissipating layers will also im-
prove the heat-sink effectiveness.
THERMAL PROTECTION
Thermal protection disables the output when the
junction temperature rises to approximately 160
°
C,
allowing the device to cool. When the junction tem-
perature cools to approximately 140
°
C, the output
circuitry is again enabled. Depending on power dissi-
pation, thermal resistance, and ambient temperature,
the thermal protection circuit may cycle on and off.
This limits the dissipation of the regulator, protecting
it from damage due to overheating.
P
D
(V
IN
V
OUT
)
I
OUT
(6)
Package Mounting
Solder
pad
TPS732xx
Solder Pad Recommendations for Surface-Mount De-
vices
(AB-132), available from the Texas Instruments
web site at www.ti.com.
TPS73201, TPS73215, TPS73216
TPS73218, TPS73225, TPS73230
TPS73233, TPS73250
SBVS037F–AUGUST 2003–REVISED SEPTEMBER 2004
(Adjustable voltage version)
reliability, thermal protection should trigger at least
35
°
C above the maximum expected ambient con-
dition of your application. This produces a worst-case
junction temperature of 125
°
C at the highest ex-
pected ambient temperature and worst-case load.
The internal protection circuitry of the TPS732xx has
been designed to protect against overload conditions.
It was not intended to replace proper heatsinking.
Continuously running the TPS732xx into thermal
shutdown will degrade device reliability.
After the enable pin is driven low, no bias voltage is
needed on any pin for reverse current blocking. Note
that reverse current is specified as the current flowing
out of the IN pin due to voltage applied on the OUT
pin. There will be additional current flowing into the
OUT pin due to the 80k
internal resistor divider to
ground (see Figure 1 and Figure 2).
The
addition
of
plated
For the TPS73201, reverse current may flow when
V
FB
is more than 1.0V above V
IN
.
Power dissipation depends on input voltage and load
conditions. Power dissipation is equal to the product
of the output current times the voltage drop across
the output pass element (V
IN
to V
OUT
):
Power dissipation can be minimized by using the
lowest possible input voltage necessary to assure the
required output voltage.
footprint
are
presented
recommendations
in
Application
for
Bulletin
the
Any tendency to activate the thermal protection circuit
indicates excessive power dissipation or an inad-
equate heatsink. For reliable operation, junction tem-
perature should be limited to 125
°
C maximum. To
estimate the margin of safety in a complete design
(including heatsink), increase the ambient tempera-
ture until the thermal protection is triggered; use
worst-case loads and signal conditions. For good
14
相關PDF資料
PDF描述
TPS73225DCQT Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection
TPS73230DCQ Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection
TPS73230DCQT Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection
TPS73233DCQT Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection
TPS73250DCQT Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection
相關代理商/技術參數
參數描述
TPS73218MDBVREP 功能描述:低壓差穩壓器 - LDO Mil Enh Cap-Free NMOS 250-mA LDO Reg RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
TPS73218QDCQRQ1 制造商:Texas Instruments 功能描述:IC REG LDO 1.8V 0.25A SOT223-6 制造商:Texas Instruments 功能描述:Single Output Linear Regulator
TPS73219DBVR 功能描述:低壓差穩壓器 - LDO Sgl Output LDO 250mA Fixed RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
TPS73219DBVRG4 功能描述:低壓差穩壓器 - LDO Sgl Out 250mA Fixed Rev Crnt Prot RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
TPS73219DBVT 功能描述:低壓差穩壓器 - LDO Sgl Output LDO 250mA Fixed RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
主站蜘蛛池模板: 博乐市| 泰来县| 博湖县| 涞源县| 隆安县| 华宁县| 沾益县| 通化市| 太原市| 福贡县| 虞城县| 阜平县| 翁源县| 四子王旗| 永宁县| 平泉县| 兰考县| 武功县| 乌海市| 阜阳市| 吴江市| 小金县| 和政县| 文水县| 晋城| 房产| 时尚| 玛纳斯县| 安塞县| 桂阳县| 南阳市| 铜鼓县| 石楼县| 黑水县| 亳州市| 武安市| 平远县| 淮北市| 静宁县| 天台县| 和静县|