- 您現在的位置：買賣IC網 > PDF目錄382681 > TPS732XX (Texas Instruments, Inc.) Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection PDF資料下載
參數資料
| 型號： | TPS732XX |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| 中文描述： | 無電容，NMOS管，150mA的低壓差穩壓器的反向電流保護 |
| 文件頁數： | 13/23頁 |
| 文件大小： | 663K |
| 代理商： | TPS732XX |
www.ti.com
dV dt
V
OUT
(R
1
C
OUT
80k
R
2
) R
LOAD
(5)
REVERSE CURRENT
The NMOS pass element of the TPS732xx provides
inherent protection against current flow from the
output of the regulator to the input when the gate of
the pass device is pulled low. To ensure that all
charge is removed from the gate of the pass
element, the enable pin must be driven low before
the input voltage is removed. If this is not done, the
pass element may be left on due to stored charge on
the gate.
POWER DISSIPATION
The ability to remove heat from the die is different for
each
package
type,
considerations in the PCB layout. The PCB area
around the device that is free of other components
moves the heat from the device to the ambient air.
Performance data for JEDEC low- and high-K boards
are shown in the Power Dissipation Ratings table.
Using heavier copper will increase the effectiveness
in removing heat from the device. The addition of
plated through-holes to heat-dissipating layers will
also improve the heat-sink effectiveness.
THERMAL PROTECTION
Thermal protection disables the output when the
junction temperature rises to approximately 160°C,
allowing the device to cool. When the junction
temperature cools
to
approximately
output circuitry is again enabled. Depending on
power dissipation, thermal resistance, and ambient
temperature, the thermal protection circuit may cycle
on and off. This limits the dissipation of the regulator,
protecting it from damage due to overheating.
P
D
(V
IN
V
OUT
)
I
OUT
(6)
Package Mounting
Solder
pad
TPS732xx are presented in Application Bulletin
Solder Pad Recommendations for Surface-Mount
Devices
(AB-132),
available
Instruments web site at www.ti.com.
TPS732xx
SBVS037I–AUGUST 2003–REVISED MAY 2006
(Adjustable voltage version)
35°C
condition of your application. This produces a
worst-case junction temperature of 125°C at the
highest
expected
ambient
worst-case load.
above
the
maximum
expected
ambient
temperature
and
The internal protection circuitry of the TPS732xx has
been
designed
to
protect
conditions. It was not intended to replace proper
heatsinking. Continuously running the TPS732xx into
thermal shutdown will degrade device reliability.
against
overload
presenting
different
After the enable pin is driven low, no bias voltage is
needed on any pin for reverse current blocking. Note
that reverse current is specified as the current
flowing out of the IN pin due to voltage applied on
the OUT pin. There will be additional current flowing
into the OUT pin due to the 80k
internal resistor
divider to ground (see
Figure 1
and
Figure 2
).
For the TPS73201, reverse current may flow when
V
FB
is more than 1.0V above V
IN
.
Power dissipation depends on input voltage and load
conditions. Power dissipation is equal to the product
of the output current times the voltage drop across
the output pass element (V
IN
to V
OUT
):
Power dissipation can be minimized by using the
lowest possible input voltage necessary to assure
the required output voltage.
140°C,
the
footprint
recommendations
for
the
Any tendency to activate the thermal protection
circuit indicates excessive power dissipation or an
inadequate heatsink. For reliable operation, junction
temperature should be limited to 125°C maximum.
To estimate the margin of safety in a complete
design (including heatsink), increase the ambient
temperature until the thermal protection is triggered;
use worst-case loads and signal conditions. For good
reliability, thermal protection should trigger at least
from
the
Texas
13
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| TPS7348QPW | LOW-DROPOUT VOLTAGE REGULATORS WITH INTEGRATED DELAYED RESET FUNCTION |
| TPS7330QPW | LOW-DROPOUT VOLTAGE REGULATORS WITH INTEGRATED DELAYED RESET FUNCTION |
| TPS7350QPW | LOW-DROPOUT VOLTAGE REGULATORS WITH INTEGRATED DELAYED RESET FUNCTION |
| TPS7301Q | LOW-DROPOUT VOLTAGE REGULATORS WITH INTEGRATED DELAYED RESET FUNCTION |
| TPS7330Q | LOW-DROPOUT VOLTAGE REGULATORS WITH INTEGRATED DELAYED RESET FUNCTION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS7330QD | 功能描述:低壓差穩壓器 - LDO Low-Dropout Voltage Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS7330QD | 制造商:Texas Instruments 功能描述:IC V REG LDO 3V SMD SOIC8 |
| TPS7330QDG4 | 功能描述:低壓差穩壓器 - LDO Low-Dropout Voltage Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS7330QDR | 功能描述:低壓差穩壓器 - LDO Low-Dropout Voltage Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS7330QDRG4 | 功能描述:低壓差穩壓器 - LDO Low-Dropout Voltage Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。