- 您現在的位置：買賣IC網 > PDF目錄98286 > TPU3035PQ TELETEXT DECODER, PQCC44 PDF資料下載
參數資料
| 型號： | TPU3035PQ |
| 元件分類： | 圖文 |
| 英文描述： | TELETEXT DECODER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 20/72頁 |
| 文件大小： | 347K |
| 代理商： | TPU3035PQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
TPU 3035, TPU 3040, TPU 3050
PRELIMINARY DATA SHEET
27
Micronas
4.2. I2C Bus Interface
Communication between TPU 3040 and host controller
is done via I2C-bus. For detailed information on the I2C-
bus please refer to the Philips manual ‘I2C-bus Specifi-
cation’.
The TPU 3040 acts as a slave transmitter/receiver and
uses clock synchronization to slow down the data trans-
fer if necessary. General call address will not be ac-
knowledged.
Different memories and functions of TPU 3040 can be
accessed by subaddressing. The byte following the
slave address byte is defined as the subaddress byte.
Maximum length of an I2C telegram is 256 bytes follow-
ing slave address and subaddress byte. The interface
supports data transfer with autoincrement.
The I2C-bus interface is interrupt-driven and uses an in-
ternal 48-byte buffer to collect I2C data in real-time with-
out disturbing internal processes. This is done to avoid
clock synchronization as far as possible. When the TPU
3040 has to process the I2C buffer and the I2C telegram
has not yet been stopped, the I2C clock line will be held
down.
The time required to process the I2C buffer depends on
other processes running inside the TPU 3040 firmware.
Thus the following I2C telegram addressing the TPU can
be held after the slave address byte until the old tele-
gram is completely processed.
4.2.1. Subaddressing
Access to all memory locations and to the command in-
terface is achieved by subaddressing. Both the external
DRAM and the internal CPU memory can be addressed
completely. The TPU 3040 acknowledges 6 different
subaddresses following the slave address (see Table
4–2).
The following symbols are used to describe the I2C ex-
ample telegrams:
<
start condition
>
stop condition
ab
address bank byte
ah
address high byte
al
address low byte
cc
command byte
dd
data byte
ss
status byte
..
0 – n continuation bytes
Table 4–2: I2C-bus Subaddresses
Name
Binary Value
Hex Value
Mode
Function
TPU
0010 001x
22, 23
W, R
TPU slave address
Sub 1
0111 1000
78
W
subaddressing CPU (static)
Sub 2
0111 1001
79
W
subaddressing CPU (autoincrement)
Sub 3
0111 1010
7A
W
subaddressing DRAM (autoincrement)
Sub 4
0111 1011
7B
W
subaddressing command language
Data
0111 1100
7C
R/W
subaddressing data register
Status
0111 1101
7D
R
status register
bit 7 = command wait
bit 6 = command invalid
bit 5 = command found no data
bit 4 = not used
bit 3 = not used
bit 2 = not used
bit 1 = 0
bit 0 = 0
相關PDF資料 |
PDF描述 |
|---|---|
| TPU3050PK | TELETEXT DECODER, PDIP40 |
| TPU3050PO | TELETEXT DECODER, PDIP52 |
| TPU3050PQ | TELETEXT DECODER, PQCC44 |
| TPU3040PK | TELETEXT DECODER, PDIP40 |
| TPU3040PO | TELETEXT DECODER, PDIP52 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPU304 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | JFET | P-CHANNEL | 30MA I(DSS) | TO-226AA |
| TPU3040 | 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Teletext Processors |
| TPU3040(DIP40) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Teletext Circuit |
| TPU3040(PDIP40) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor |
| TPU3040(PSDIP52) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor |
發布緊急采購，3分鐘左右您將得到回復。