欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TRF7961RHBT
廠商: TEXAS INSTRUMENTS INC
元件分類: 消費家電
英文描述: SPECIALTY CONSUMER CIRCUIT, PQCC32
封裝: 5 X 5 MM, GREEN, PLASTIC, QFN-32
文件頁數: 15/52頁
文件大小: 1023K
代理商: TRF7961RHBT
SLOU186F – AUGUST 2006 – REVISED AUGUST 2010
www.ti.com
5.2.4
Direct Mode
Direct mode allows the user to configure the reader in one of two ways. Direct mode 0 (bit 6 = 0, as
defined in ISO control register) allows the user to use only the front-end functions of the reader, bypassing
the protocol implementation in the reader. For transmit functions, the user has direct access to the
transmit modulator through the MOD pin (pin 14). On the receive side, the user has direct access to the
sub-carrier signal (digitized RF envelope signal) on I/O_6 (pin 23).
Direct mode1 (bit 6 = 1, as defined in ISO control register) uses the sub-carrier signal decoder of the
selected protocol (as defined in ISO control register). This means that the receive output is not the
sub-carrier signal but the decoded serial bit stream and bit clock signals. The serial data is available on
I/O_6 (pin 23) and the bit clock is available on I/O_5 (pin 22). The transmit side is identical; the user has
direct control over the RF modulation through the MOD input. This mode is provided so that the user can
implement a protocol that has the same bit coding as one of the protocols implemented in the reader, but
needs a different framing format.
To select direct mode, the user must first choose which direct mode to enter by writing B6 in the ISO
control register. This bit determines if the receive output is the direct sub-carrier signal (B6 = 0) or the
serial data of the selected decoder. If B6 = 1, then the user must also define which protocol should be
used for bit decoding by writing the appropriate setting in the ISO control register.
The reader actually enters the direct mode when B6 (direct) is set to 1 in the chip status control register.
Direct mode starts immediately. The write command should not be terminated with a stop condition (see
communication protocol), because the stop condition terminates the direct mode and clears B6. This is
necessary as the direct mode uses one or two I/O pins (I/O_6, I/O_5). Normal parallel communication is
not possible in direct mode. Sending a stop condition terminates direct mode.
Figure 5-4 shows the different configurations available in direct mode.
In mode 0, the reader is used as an AFE only, and protocol handling is bypassed.
In mode 1, framing is not done, but SOF and EOF are present. This allows for a user-selectable
framing level based on an existing ISO standard.
In mode 2, data is ISO-standard formatted. SOF, EOF, and error checking are removed, so the
microprocessor receives only bytes of raw data via a 12-byte FIFO.
22
System Description
Copyright 2006–2010, Texas Instruments Incorporated
Product Folder Link(s): TRF7960 TRF7961
相關PDF資料
PDF描述
TS(X)8387MFDSSC/SMD 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68
TS(X)8387MF_ 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68
TS(X)8387VF_ 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68
TS(X)8387VF 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68
TS8387MFB/C 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68
相關代理商/技術參數
參數描述
TRF7961RHBT 制造商:Texas Instruments 功能描述:RFID Reader IC
TRF7961RHBTG4 功能描述:RFID應答器 Multi-Standard High Freq RFID Read/Writ RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
TRF7962A 制造商:TI 制造商全稱:Texas Instruments 功能描述:FULLY INTEGRATED 13.56-MHz RFID READER/WRITER IC FOR ISO15693/ISO18000-3 STANDARDS
TRF7962ARHBR 功能描述:RFID應答器 Fully Integ 13.56MHz RFID R/W IC RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
TRF7962ARHBT 功能描述:RFID應答器 Fully Integ 13.56MHz RFID R/W IC RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
主站蜘蛛池模板: 晋宁县| 浦北县| 商水县| 广饶县| 布尔津县| 天峻县| 迭部县| 温泉县| 蓝山县| 澄江县| 霞浦县| 尚义县| 开阳县| 阿城市| 乌鲁木齐市| 苏尼特右旗| 湘阴县| 辽宁省| 宜昌市| 台东市| 栾城县| 桐柏县| 夏河县| 互助| 岢岚县| 公安县| 南平市| 北碚区| 墨竹工卡县| 潜山县| 兴国县| 巩义市| 清远市| 板桥市| 富宁县| 余庆县| 阳新县| 庆阳市| 信宜市| 达拉特旗| 嘉义市|