- 您現在的位置：買賣IC網 > PDF目錄98290 > TS5A21366RSER (TEXAS INSTRUMENTS INC) DUAL 1-CHANNEL, SGL POLE SGL THROW SWITCH, PQCC8 PDF資料下載
參數資料
| 型號： | TS5A21366RSER |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 多路復用及模擬開關 |
| 英文描述： | DUAL 1-CHANNEL, SGL POLE SGL THROW SWITCH, PQCC8 |
| 封裝： | PLASTIC, MO-288UECD, QFN-8 |
| 文件頁數： | 4/29頁 |
| 文件大小： | 862K |
| 代理商： | TS5A21366RSER |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
SCDS285A – MARCH 2009 – REVISED OCTOBER 2009................................................................................................................................................. www.ti.com
PARAMETER DESCRIPTION
SYMBOL
DESCRIPTION
VCOM
Voltage at COM
VNO
Voltage at NO
ron
Resistance between COM and NO ports when the channel is ON
ron(flat)
Difference between the maximum and minimum value of ron in a channel over the specified range of conditions
INO(OFF)
Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the OFF state
Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the ON state and the output
INO(ON)
(COM) open
ICOM(OFF)
Leakage current measured at the COM port, with the corresponding channel (COM to NO) in the OFF state
Leakage current measured at the COM port, with the corresponding channel (COM to NO) in the ON state and the output
ICOM(ON)
(NO) open
VIH
Minimum input voltage for logic high for the control input (IN)
VIL
Maximum input voltage for logic low for the control input (IN)
VI
Voltage at the control input (IN)
IIH, IIL
Leakage current measured at the control input (IN)
Turn-on time for the switch. This parameter is measured under the specified range of conditions and by the propagation
tON
delay between the digital control (IN) signal and analog output (COM or NO) signal when the switch is turning ON.
Turn-off time for the switch. This parameter is measured under the specified range of conditions and by the propagation
tOFF
delay between the digital control (IN) signal and analog output (COM or NO) signal when the switch is turning OFF.
Charge injection is a measurement of unwanted signal coupling from the control (IN) input to the analog (NO or COM)
QC
output. This is measured in coulomb (C) and measured by the total charge induced due to switching of the control input.
Charge injection, QC = CL × ΔVCOM, CL is the load capacitance and ΔVCOM is the change in analog output voltage.
CNO(OFF)
Capacitance at the NO port when the corresponding channel (NO to COM) is OFF
CNO(ON)
Capacitance at the NO port when the corresponding channel (NO to COM) is ON
CCOM(OFF)
Capacitance at the COM port when the corresponding channel (COM to NO) is OFF
CCOM(ON)
Capacitance at the COM port when the corresponding channel (COM to NO) is ON
CI
Capacitance of control input (IN)
OFF isolation of the switch is a measurement of OFF-state switch impedance. This is measured in dB in a specific
OISO
frequency, with the corresponding channel (NO to COM) in the OFF state.
Crosstalk is a measurement of unwanted signal coupling from an ON channel to an OFF channel (NO1 to NO2). This is
XTALK
measured in a specific frequency and in dB.
BW
Bandwidth of the switch. This is the frequency in which the gain of an ON channel is –3 dB below the DC gain.
Total harmonic distortion describes the signal distortion caused by the analog switch. This is defined as the ratio of root
THD
mean square (RMS) value of the second, third, and higher harmonic to the absolute magnitude of the fundamental
harmonic.
I+
Static power-supply current with the control (IN) pin at V+ or GND
ΔI+
This is the increase in I+ for each control (IN) input that is at the specified voltage, rather than at V+ or GND.
12
Copyright 2009, Texas Instruments Incorporated
Product Folder Link(s): TS5A21366
相關PDF資料 |
PDF描述 |
|---|---|
| TS5A22366YFCR | DUAL 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, BGA12 |
| TS5A23157RSER | DUAL 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, PQCC10 |
| TS5A23157RSERG4 | DUAL 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, PQCC10 |
| TS5A23157DGSRG4 | DUAL 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, PDSO10 |
| TS5A23157TDGSRQ1 | SGL POLE DOUBLE THROW SWITCH, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TS5A22362 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:0.65-ヘ DUAL SPDT ANALOG SWITCHES WITH NEGATIVE SIGNALING CAPABILITY |
| TS5A22362_1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:0.65-Ω DUAL SPDT ANALOG SWITCHES WITH NEGATIVE SIGNALING CAPABILITY |
| TS5A22362_10 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:0.65-Ω DUAL SPDT ANALOG SWITCHES WITH NEGATIVE SIGNALING CAPABILITY |
| TS5A22362_11 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:0.65-Ω DUAL SPDT ANALOG SWITCHES WITH NEGATIVE SIGNALING CAPABILITY |
| TS5A22362DGSR | 功能描述:模擬開關 IC 0.65Ohm Dual SPDT Ana Sw RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。