- 您現在的位置：買賣IC網 > PDF目錄98291 > TS5A63157YEPR (TEXAS INSTRUMENTS INC) 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, BGA6 PDF資料下載
參數資料
| 型號： | TS5A63157YEPR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 多路復用及模擬開關 |
| 英文描述： | 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, BGA6 |
| 封裝： | WCSP-6 |
| 文件頁數： | 8/30頁 |
| 文件大小： | 737K |
| 代理商： | TS5A63157YEPR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
SCDS203A – DECEMBER 2005 – REVISED JULY 2009................................................................................................................................................... www.ti.com
PARAMETER DESCRIPTION
SYMBOL
DESCRIPTION
VCOM
Voltage at COM
VNC
Voltage at NC
VNO
Voltage at NO
ron
Resistance between COM and NC or COM and NO ports when the channel is ON
rpeak
Peak on-state resistance over a specified voltage range
Δron
Difference of ron between channels in a specific device
ron(flat)
Difference between the maximum and minimum value of ron in a channel over the specified range of conditions
INC(OFF)
Leakage current measured at the NC port, with the corresponding channel (NC to COM) in the OFF state
INC(PWROFF)
Leakage current measured at the NC port during the power-down condition, V+ = 0
INO(OFF)
Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the OFF state
INO(PWROFF)
Leakage current measured at the NO port during the power-down condition, V+ = 0
Leakage current measured at the NC port, with the corresponding channel (NC to COM) in the ON state and the output
INC(ON)
(COM) open
Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the ON state and the output
INO(ON)
(COM) open
Leakage current measured at the COM port, with the corresponding channel (COM to NO or COM to NC) in the ON state
ICOM(ON)
and the output (NC or NO) open
ICOM(PWROFF)
Leakage current measured at the COM port during the power-down condition, V+ = 0
VIH
Minimum input voltage for logic high for the control input (IN)
VIL
Maximum input voltage for logic low for the control input (IN)
VI
Voltage at the control input (IN)
IIH, IIL
Leakage current measured at the control input (IN)
Turn-on time for the switch. This parameter is measured under the specified range of conditions and by the propagation
tON
delay between the digital control (IN) signal and analog output (COM or NO) signal when the switch is turning ON.
Turn-off time for the switch. This parameter is measured under the specified range of conditions and by the propagation
tOFF
delay between the digital control (IN) signal and analog output (COM or NO) signal when the switch is turning OFF.
Break-before-make time. This parameter is measured under the specified range of conditions and by the propagation
tBBM
delay between the output of two adjacent analog channels (NC and NO) when the control signal changes state.
Charge injection is a measurement of unwanted signal coupling from the control (IN) input to the analog (NO or COM)
QC
output. This is measured in coulomb (C) and measured by the total charge induced due to switching of the control
input.Charge injection, QC = CL × ΔVCOM, CL is the load capacitance and ΔVCOM is the change in analog output voltage.
CNC(OFF)
Capacitance at the NC port when the corresponding channel (NC to COM) is OFF
CNO(OFF)
Capacitance at the NO port when the corresponding channel (NO to COM) is OFF
CNC(ON)
Capacitance at the NC port when the corresponding channel (NC to COM) is ON
CNO(ON)
Capacitance at the NO port when the corresponding channel (NO to COM) is ON
CCOM(ON)
Capacitance at the COM port when the corresponding channel (COM to NC or COM to NO) is ON
CI
Capacitance of control input (IN)
OFF isolation of the switch is a measurement of OFF-state switch impedance. This is measured in dB in a specific
OISO
frequency, with the corresponding channel (NC to COM or NO to COM) in the OFF state.
Crosstalk is a measurement of unwanted signal coupling from an ON channel to an OFF channel (NC to NO or NO to
XTALK
NC). This is measured in a specific frequency and in dB.
BW
Bandwidth of the switch. This is the frequency in which the gain of an ON channel is –3 dB below the DC gain.
Total harmonic distortion is defined as the ratio of the root mean square (RMS) value of the second, third, and higher
THD
harmonics to the magnitude of fundamental harmonic.
I+
Static power-supply current with the control (IN) pin at V+ or GND
Output voltage during an undershoot event. This is measured by turning off a specific channel and applying an
VOUTU
undershoot voltage at the input of the switch.
Output voltage during an overshoot event. This is measured by turning off a specific channel and applying an overshoot
VOUTO
voltage at the input of the switch.
16
Copyright 2005–2009, Texas Instruments Incorporated
Product Folder Link(s): TS5A63157
相關PDF資料 |
PDF描述 |
|---|---|
| TS5A6542RSER | 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, QCC8 |
| TS5USBA43402YZPR | SPECIALTY ANALOG CIRCUIT, PBGA20 |
| TS83006CE1 | 1-CH 6-BIT FLASH METHOD ADC, PARALLEL ACCESS, CQCC68 |
| TS83006ME1B/C | 1-CH 6-BIT FLASH METHOD ADC, PARALLEL ACCESS, CQCC68 |
| TS83006ME1 | 1-CH 6-BIT FLASH METHOD ADC, PARALLEL ACCESS, CQCC68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TS5A63157YZPR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:12-OHM SPDT ANALOG SWITCH |
| TS5A6542 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:0.75-Ω SPDT ANALOG SWITCH WITH INPUT LOGIC TRANSLATION |
| TS5A6542_09 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:0.75-Ω SPDT ANALOG SWITCH WITH INPUT LOGIC TRANSLATION |
| TS5A6542YZPR | 功能描述:模擬開關 IC 0.75-Ohm SPDT Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| TS5A6542YZTR | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。