- 您現在的位置：買賣IC網 > PDF目錄365955 > TS80C188EC-20 16-Bit Microprocessor PDF資料下載
參數資料
| 型號： | TS80C188EC-20 |
| 元件分類： | 16位微控制器 |
| 英文描述： | 16-Bit Microprocessor |
| 中文描述： | 16位微處理器 |
| 文件頁數： | 40/57頁 |
| 文件大小： | 585K |
| 代理商： | TS80C188EC-20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
80C186EC/188EC, 80L186EC/188EC
DERATING CURVES
272434–13
Figure 14. Typical Output Delay Variations versus Load Capacitance
272434–14
Figure 15. Typical Rise and Fall Variations versus Load Capacitance
RESET
The processor will perform a reset operation any
time the RESIN pin is active. The RESIN pin is syn-
chronized before it is presented internally, which
means that the clock must be operating before a
reset can take effect. From a power-on state, RESIN
must be held active (low) in order to guarantee cor-
rect initialization of the processor.
Failure to pro-
vide RESIN while the device is powering up will
result in unspecified operation of the device.
Figure 16 shows the correct reset sequence when
first applying power to the processor. An external
clock connected to CLKIN must not exceed the V
CC
threshold being applied to the processor. This is nor-
mally not a problem if the clock driver is supplied
with the same V
CC
that supplies the processor.
When attaching a crystal to the device, RESIN must
remain active until both V
CC
and CLKOUT are stable
(the length of time is application specific and de-
pends on the startup characteristics of the crystal
circuit). The RESIN pin is designed to operate cor-
rectly using a RC reset circuit, but the designer must
ensure that the ramp time for V
CC
is not so long that
RESIN is never sampled at a logic low level when
V
CC
reaches minimum operating conditions.
Figure 17 shows the timing sequence when RESIN
is applied after V
CC
is stable and the device has
been operating. Note that a reset will terminate all
activity and return the processor to a known operat-
ing state. Any bus operation that is in progress at the
time RESIN is asserted will terminate immediately
(note that most control signals will be driven to their
inactive state first before floating).
While
A19/S16/ONCE and A18:16 are configured as in-
puts and weakly held high by internal pullup transis-
tors. Only A19/ONCE can be overdriven to a low
and is used to enable the ONCE Mode. Forcing
LOCK or A18:16 low at any time while RESIN is low
is prohibited and will cause unspecified device oper-
ation.
RESIN
is
active,
bus
signals
LOCK,
40
相關PDF資料 |
PDF描述 |
|---|---|
| TS80L186EC13 | MICROPROCESSOR|16-BIT|CMOS|QFP|100PIN|PLASTIC |
| TS80C186EC13 | MICROPROCESSOR|16-BIT|CMOS|QFP|100PIN|PLASTIC |
| TS80C186EC20 | MICROPROCESSOR|16-BIT|CMOS|QFP|100PIN|PLASTIC |
| TS80L186EC-13 | 16-Bit Microprocessor |
| TS80L188EC13 | MICROPROCESSOR|16-BIT|CMOS|QFP|100PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TS80C188XL10 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor |
| TS80C188XL12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROPROCESSOR|16-BIT|CMOS|QFP|80PIN|PLASTIC |
| TS80C188XL-16 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microprocessor |
| TS80C188XL20 | 功能描述:IC MPU 16-BIT 5V 20MHZ 80-MQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:- 標準包裝:2 系列:MPC8xx 處理器類型:32-位 MPC8xx PowerQUICC 特點:- 速度:133MHz 電壓:3.3V 安裝類型:表面貼裝 封裝/外殼:357-BBGA 供應商設備封裝:357-PBGA（25x25） 包裝:托盤 |
| TS80C194 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。