- 您現在的位置：買賣IC網 > PDF目錄365959 > TS80C31X2-LLBB (ATMEL CORP) 8-bit CMOS Microcontroller ROMless PDF資料下載
參數資料
| 型號： | TS80C31X2-LLBB |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-bit CMOS Microcontroller ROMless |
| 中文描述： | 8-BIT, 30 MHz, MICROCONTROLLER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 13/40頁 |
| 文件大?。?/td> | 484K |
| 代理商： | TS80C31X2-LLBB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Rev. A - Mar. 19, 1999
13
Preliminary
TS80C31X2
Software may examine FE bit after each reception to check for data errors. Once set, only software or a reset can
clear FE bit. Subsequently received frames with valid stop bits cannot clear FE bit. When FE feature is enabled,
RI rises on stop bit instead of the last data bit (See Figure 5. and Figure 6.).
Figure 5. UART Timings in Mode 1
Figure 6. UART Timings in Modes 2 and 3
6.3.2 Automatic Address Recognition
The automatic address recognition feature is enabled when the multiprocessor communication feature is enabled
(SM2 bit in SCON register is set).
Implemented in hardware, automatic address recognition enhances the multiprocessor communication feature by
allowing the serial port to examine the address of each incoming command frame. Only when the serial port
recognizes its own address, the receiver sets RI bit in SCON register to generate an interrupt. This ensures that
the CPU is not interrupted by command frames addressed to other devices.
If desired, you may enable the automatic address recognition feature in mode 1. In this configuration, the stop bit
takes the place of the ninth data bit. Bit RI is set only when the received command frame address matches the
device’s address and is terminated by a valid stop bit.
To support automatic address recognition, a device is identified by a given address and a broadcast address.
NOTE: The multiprocessor communication and automatic address recognition features cannot be enabled in mode 0 (i.e. setting SM2 bit in SCON
register in mode 0 has no effect).
Data byte
RI
SMOD0=X
Stop
bit
Start
bit
RXD
D7
D6
D5
D4
D3
D2
D1
D0
FE
SMOD0=1
RI
SMOD0=0
Data byte
Ninth
bit
Stop
bit
Start
bit
RXD
D8
D7
D6
D5
D4
D3
D2
D1
D0
RI
SMOD0=1
FE
SMOD0=1
相關PDF資料 |
PDF描述 |
|---|---|
| TS80C31X2-LLBD | GT 24C 24#16 PIN PLUG |
| TS80C31X2-LLBR | GT 24C 24#16 SKT PLUG |
| TS80C31X2-LLCB | 8-bit CMOS Microcontroller ROMless |
| TS80C31X2-LLCD | 8-bit CMOS Microcontroller ROMless |
| TS80C31X2-LLCR | 8-bit CMOS Microcontroller ROMless |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TS80C31X2-LLBD | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit CMOS Microcontroller ROMless |
| TS80C31X2-LLBR | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit CMOS Microcontroller ROMless |
| TS80C31X2-LLCB | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit CMOS Microcontroller ROMless |
| TS80C31X2-LLCD | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit CMOS Microcontroller ROMless |
| TS80C31X2-LLCR | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit CMOS Microcontroller ROMless |
發布緊急采購，3分鐘左右您將得到回復。