- 您現在的位置：買賣IC網 > PDF目錄98293 > TS8308500CG (ATMEL CORP) 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CBGA72 PDF資料下載
參數資料
| 型號： | TS8308500CG |
| 廠商： | ATMEL CORP |
| 元件分類： | ADC |
| 英文描述： | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CBGA72 |
| 封裝： | 1.27 MM PITCH, HEAT SINK, CERAMIC, BGA-72 |
| 文件頁數： | 22/42頁 |
| 文件大?。?/td> | 641K |
| 代理商： | TS8308500CG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
29
Preliminary Specification
ββββ-site
TS8308500
7.2.
PRINCIPLE OF DATA READY SIGNAL CONTROL BY DRRB INPUT COMMAND
7.2.1.
DATA READY OUTPUT SIGNAL RESET
The Data Ready signal is reset on falling edge of DRRB input command, on ECL logical low level (-1.8V). DRRB may also be tied to VEE = - 5V
for Data Ready output signal Master Reset. So long DRRB remains at logical low level, (or tied to VEE = - 5V), the Data Ready output remains
at logical zero and is independent of the external free running encoding clock.
The Data Ready output signal (DR,DRB) is reset to logical zero after TRDR= 720 ps typical.
TRDR is measured between the -1.3V point of the falling edge of DRRB input command and the zero crossing point of the differential Data
Ready output signal (DR,DRB).
The Data Ready Reset command may be a pulse of 1 ns minimum time width.
7.2.2.
DATA READY OUTPUT SIGNAL RESTART
The Data Ready output signal restarts on DRRB command rising edge, ECL logical high levels (-0.8V).
DRRB may also be Grounded, or is allowed to float, for normal free running Data Ready output signal.
The Data Ready signal restart sequence depends on the logical level of the external encoding clock, at DRRB rising edge instant :
1)
The DRRB rising edge occurs when external encoding clock input (CLK,CLKB) is LOW :
The Data Ready output first rising edge occurs after half a clock period on the clock falling edge, after a delay time TDR = 1320 ps already
defined hereabove.
2)
The DRRB rising edge occurs when external encoding clock input (CLK,CLKB) is HIGH :
The Data Ready output first rising edge occurs after one clock period on the clock falling edge, and a delay TDR = 1320ps.
Consequently, as the analog input is sampled on clock rising edge, the first digitized data corresponding to the first acquisition ( N ) after Data
Ready signal restart ( rising edge ) is always strobed by the third rising edge of the data ready signal.
The time delay (TD1) is specified between the last point of a change in the differential output data (zero crossing point) to the rising or falling
edge of the differential Data Ready signal (DR,DRB) (zero crossing point).
Note 1 : For normal initialization of Data Ready output signal, the external encoding clock signal frequency and level must be controlled.
It is reminded that the minimum encoding clock sampling rate for the ADC is 10 MSPS and consequently the clock cannot be stopped.
Note 2 : One single pin is used for both DRRB input command and die junction temperature monitoring.
Pin denomination will be DRRB/DIOD.( On former version denomination was DIOD. )
Temperature monitoring and Data Ready control by DRRB is not possible simultaneously.
7.3.
ANALOG INPUTS (VIN) (VINB)
The analog input Full Scale range is 0.5 Volts peak to peak (Vpp), or -2 dBm into the 50 ohms termination resistor.
In differential mode input configuration, that means 0.25 Volt on each input, or +/- 125 mV around zero volt. The input common mode is
GROUND.
The typical input capacitance is 3 pF for TS8308500 in CBGA package.
Differential inputs voltage span
-125
125
[mV]
-250 mV
250 mV
VIN
500mV
Full Scale
analog input
t
VINB
(VIN,VINB) = +/- 250 mV = 500 mV diff
0 Volt
相關PDF資料 |
PDF描述 |
|---|---|
| TS83102G0BMGS | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CBGA152 |
| TS83102G0BMGS | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CBGA152 |
| TS83102G0BVGL | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CBGA152 |
| TS83102G0BCGL | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CBGA152 |
| TS83110CZT | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CDFP28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TS8308500CGL | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:ADC 8-bit 500 Msps |
| TS8308500VGL | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:ADC 8-bit 500 Msps |
| TS8308C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Converter IC |
| TS8308J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Converter IC |
| TS8308P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Converter IC |
發布緊急采購，3分鐘左右您將得到回復。