- 您現在的位置：買賣IC網 > PDF目錄98298 > TS8388BCFS9QB3ZB9 (E2V TECHNOLOGIES PLC) 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 PDF資料下載
參數資料
| 型號： | TS8388BCFS9QB3ZB9 |
| 廠商： | E2V TECHNOLOGIES PLC |
| 元件分類： | ADC |
| 英文描述： | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| 封裝： | CERAMIC, QFP-68 |
| 文件頁數： | 20/43頁 |
| 文件大小： | 825K |
| 代理商： | TS8388BCFS9QB3ZB9 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
TS8388BFS
27/42
Preliminary Beta Site
7.
APPLYING THE TS8388BFS
7.1.
TIMING INFORMATIONS
7.1.1.
TIMING VALUE FOR TS8388BFS
Timing values as defined in 3.3 are advanced datas, issuing from electric simulations fitted with measurements.
Timing values are given at CQFP68 package inputs/outputs, taking into account package internal controlled impedance traces propagation
delays, gullwing pin model, and specified termination loads.
Propagation delays in 50/75 ohms impedance traces are NOT taken into account for TOD and TDR.
Apply proper derating values corresponding to termination topology.
The min/max timing values are valid over the full temperature range in the following conditions :
Note 1 : Specified Termination Load (Differential output Datas and Data Ready) :
50 ohms resistor in parallel with 1 standard ECLinPS register from Motorola, (e.g : 10E452)
(Typical ECLinPS inputs shows a typical input capacitance of 1.5 pF (including package and ESD protections)
If addressing an output Dmux, take care if some Digital outputs do not have the same termination load and apply corresponding derating value
given below.
Note 2 : Output Termination Load derating values for TOD and TDR :
~ 35 ps/pF or 50 ps per additionnal ECLinPS load.
Note 3 :Propagation time delay derating values have also to be applied for TOD and TDR :
~ 6 ps/mm (155 ps/inch) for TSEV8388B Evaluation Board.
Apply proper time delay derating value if a different dielectric layer is used.
7.1.2.
PROPAGATION TIME CONSIDERATIONS
TOD and TDR Timing values are given from pin to pin and DO NOT include the additionnal propagation times between device pins and
input/output termination loads. For the TSEV8388B Evaluation Board, the propagation time delay is 6ps/mm (155ps/inch) corresponding to 3.4
(@10GHz) dielectric constant of the RO4003 used for the Board.
If a different dielectric layer is used (for instance Teflon), please use appropriate propagation time values.
TD does NOT depend on propagation times because it is a differential data.
(TD is the time difference between Data Ready output delay and digital Data output delay)
TD is also the most straightforward data to measure, again because it is differential :
TD can be measured directly onto termination loads, with matched Oscilloscopes probes.
7.1.3.
TOD - TDR VARIATION OVER TEMPERATURE
Values for TOD and TDR track each other over temperature (1 percent variation for TOD - TDR per 100 degrees Celsius temperature variation).
Therefore TOD - TDR variation over temperature is negligible. Moreover, the internal (onchip) and package skews between each Data TODs
and TDR effect can be considered as negligible.
Consequently, minimum values for TOD and TDR are never more than 100 ps apart. The same is true for the TOD and TDR maximum values.
In other terms :
If TOD is at 1150 ps, TDR will not be at 1620 ps ( maximum time delay for TDR ).
If TOD is at 1660 ps, TDR will not be at 1110 ps ( minimum time delay for TDR ) However, external TOD - TDR values may be dictated by total
digital datas skews between every TODs (each digital data) and TDR :
MCM Board , bonding wires and output lines lengths differences, and output termination impedance mismatches.
The external (on board) skew effect has NOT been taken into account for the specification of the minimum and maximum values for TOD-TDR.
7.1.4.
PRINCIPLE OF OPERATION
The Analog input is sampled on the rising edge of external clock input (CLK,CLKB) after TA (aperture delay) of typically 250ps .
The digitized data is available after 4 clock periods latency (pipeline delay (TPD)), on clock rising edge, after 1360 ps typical propagation delay
TOD.
The Data Ready differential output signal frequency (DR,DRB) is half the external clock frequency, that is it switches at the same rate as the
digital outputs.
The Data Ready output signal (DR,DRB) switches on external clock falling edge after a propagation delay TDR of typically 1320 ps.
A Master Asynchronous Reset input command DRRB ( ECL compatible single-ended input) is available for initializing the differential Data
Ready output signal ( DR,DRB ) .This feature is mandatory in certain applications using interleaved ADCs or using a single ADC with
demultiplexed outputs. Actually, without Data Ready signal initialization, it is impossible to store the output digital datas in a defined order.
相關PDF資料 |
PDF描述 |
|---|---|
| TS8388BCFS9QC2ZB9 | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS8388BMFS9NB3ZB9 | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS8388BMFS9NC1ZB9 | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS8388BMFS9NC2ZB9 | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS8388BMFS9QC1ZB9 | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TS8388BCG | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:A/D CONVERTER |
| TS8388BCGL | 制造商:e2v technologies 功能描述:ADC 8-BIT 1 GSPS - Trays |
| TS8388BCGL (+LID) | 制造商:e2v technologies 功能描述:ADC 8-BIT 1 GSPS - Trays |
| TS8388BMF | 制造商:e2v technologies 功能描述:ADC 8-BIT 1 GSPS - Trays |
| TS8388BMFB/Q | 制造商:e2v technologies 功能描述:ADC 8-BIT 1 GSPS - Trays |
發布緊急采購，3分鐘左右您將得到回復。