- 您現在的位置：買賣IC網 > PDF目錄365967 > TSA5060A (NXP Semiconductors N.V.) 1.3 GHz I2C-bus controlled low phase noise frequency synthesizer PDF資料下載
參數資料
| 型號： | TSA5060A |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 1.3 GHz I2C-bus controlled low phase noise frequency synthesizer |
| 中文描述： | 1.3千兆赫的I2C控制的低相位噪聲頻率合成器總線 |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 119K |
| 代理商： | TSA5060A |
2000 Oct 24
10
Philips Semiconductors
Product specification
1.3 GHz I
2
C-bus controlled low phase
noise frequency synthesizer
TSA5060A
XT/COMP frequency output
It is possible to output either the crystal or the comparison
frequency at pin XT/COMP to be used in the application.
For example, to drive a second PLL synthesizer saving a
quartz crystal. To output f
xtal
it is necessary to set bit XCE
to logic 1 and bit XCS to logic 0, or bit XCE to logic 0 and
bit XCS to logic 1 during a test mode, while to output f
comp
it is necessary to set both bits XCE and XCS to logic 1.
Iftheoutputsignalatthispinisnotuseditisrecommended
to disable it by setting both bits XCE and XCS to logic 0.
Table 10 shows how this pin is programmed. At power-on,
the XT/COMP output is set with the f
xtal
signal selected.
Prescaler enable
The TSA5060A is able to work with the relationship
f
comp
= step size for an input frequency up to 1.3 GHz,
covering the complete terrestrial and cable frequency
range.
If needed, the prescaler can be selected by setting bit PE
to logic 1 while it is not in use if bit PE is set to logic 0.
If it is important to reach a low phase noise on the
controlled VCO, it is recommended to set bit PE to logic 0
and not to use the prescaler allowing the comparison
frequency to be equal to the step size.
Test modes
It is possible to access the test modes by setting bit XCE
to logic 0 and bit XCS to logic 1. One specific test mode is
then selected using bits T2, T1 and T0, as described in
Table 10.
Table 10
XT/COMP and test mode selection; note 1
Notes
1.
2.
X = don’t care.
Status at Power-on reset.
XCE
XCS
T2
T1
T0
XT/COMP OUTPUT
TEST MODE
0
1
1
0
0
0
1
1
X
X
X
0
X
X
X
0
X
X
X
0
disabled
f
xtal
f
comp
f
xtal
normal operation
normal operation
normal operation
test operation: charge pump sink;
status byte bit FL = 1
test operation: charge pump source;
status byte bit FL = 0
test operation: charge pump disabled;
status byte bit FL = 0
test operation:
1
2
f
DIV
switched to Port P0
test operation: drive voltage (pin DRIVE)
is off (high-impedance); note 2
0
1
0
0
1
f
xtal
0
1
0
1
0
f
xtal
0
0
1
1
0
1
1
X
1
X
f
xtal
f
xtal
相關PDF資料 |
PDF描述 |
|---|---|
| TSA5060AT | 1.3 GHz I2C-bus controlled low phase noise frequency synthesizer |
| TSA5060ATS | 1.3 GHz I2C-bus controlled low phase noise frequency synthesizer |
| TSA5511TD-T | IC ACEX 1K FPGA 10K 256-FBGA |
| TSA5512ATD-T | IC,FPGA,72-CELL,CMOS,QFP,208PIN,PLASTIC |
| TSA5512TD-T | IC ACEX 1K FPGA 10K 100-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSA5060AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.3 GHz I2C-bus controlled low phase noise frequency synthesizer |
| TSA5060AT/C1,518 | 功能描述:IC SYNTH FREQ 1.3GHZ 16-SOIC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 產品變化通告:Product Discontinuation 04/May/2011 標準包裝:96 系列:- 類型:時鐘倍頻器，零延遲緩沖器 PLL:帶旁路 輸入:LVTTL 輸出:LVTTL 電路數:1 比率 - 輸入:輸出:1:8 差分 - 輸入:輸出:無/無 頻率 - 最大:133.3MHz 除法器/乘法器:是/無 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:管件 其它名稱:23S08-5HPGG |
| TSA5060AT/C2,118 | 制造商:NXP Semiconductors 功能描述: |
| TSA5060AT/C2,518 | 制造商:NXP Semiconductors 功能描述: |
| TSA5060ATS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.3 GHz I2C-bus controlled low phase noise frequency synthesizer |
發布緊急采購，3分鐘左右您將得到回復。