- 您現在的位置：買賣IC網 > PDF目錄365967 > TSA5526T (NXP SEMICONDUCTORS) ELECTRICAL POWER CORD PDF資料下載
參數資料
| 型號： | TSA5526T |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | XO, clock |
| 英文描述： | ELECTRICAL POWER CORD |
| 中文描述： | PLL FREQUENCY SYNTHESIZER, 1300 MHz, PDSO16 |
| 封裝： | 3.90 MM, PLASTIC, SO-16 |
| 文件頁數： | 23/28頁 |
| 文件大小： | 290K |
| 代理商： | TSA5526T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁
1996 Sep 24
23
Philips Semiconductors
Product specification
1.3 GHz universal bus-controlled
TV synthesizers
TSA5526; TSA5527
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook”(order code 9398 652 90011).
Reflow soldering
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250
°
C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45
°
C.
Wave soldering
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
The longitudinal axis of the package footprint must be
parallel to the solder flow.
The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within
6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°
C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| TSA5527AM | 1.3 GHz universal bus-controlled TV synthesizers |
| TSA5527AT | 1.3 GHz universal bus-controlled TV synthesizers |
| TSB12LV32-EP | IC APEX 20KE FPGA 100K 324-FBGA |
| TSB12LV01B-EP | FPGA (Field-Programmable Gate Array) |
| TSB12LV01BPZ | FPGA (Field-Programmable Gate Array) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSA5526TD-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C-Bus Frequency Synthesizer |
| TSA5527 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.3 GHz universal bus-controlled TV synthesizers |
| TSA5527AM | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.3 GHz universal bus-controlled TV synthesizers |
| TSA5527AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.3 GHz universal bus-controlled TV synthesizers |
| TSA5527M | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.3 GHz universal bus-controlled TV synthesizers |
發布緊急采購，3分鐘左右您將得到回復。