- 您現在的位置：買賣IC網 > PDF目錄98301 > TSC2008IRGVR (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQCC16 PDF資料下載
參數資料
| 型號： | TSC2008IRGVR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQCC16 |
| 封裝： | 4 X 4 MM, GREEN, PLASTIC, VQFN-16 |
| 文件頁數： | 25/40頁 |
| 文件大小： | 1028K |
| 代理商： | TSC2008IRGVR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
LAYOUT
www.ti.com.......................................................................................................................................................... SBAS406B – JUNE 2008 – REVISED MARCH 2009
The following layout suggestions should obtain optimum performance from the TSC2008. Keep in mind that
many portable applications have conflicting requirements for power, cost, size, and weight. In general, most
portable devices have fairly clean power and grounds because most of the internal components are very low
power. This situation would mean less bypassing for the converter power and less concern regarding grounding.
However, each situation is unique and the following suggestions should be reviewed carefully.
For optimum performance, care should be taken with the physical layout of the TSC2008 circuitry. The basic
SAR architecture is sensitive to glitches or sudden changes on the power supply, reference, ground connections,
and digital inputs that occur just before latching the output of the analog comparator. Therefore, during any single
conversion for an n-bit SAR converter, there are n windows in which large external transient voltages can easily
affect the conversion result. Such glitches might originate from switching power supplies, nearby digital logic, and
high power devices. The degree of error in the digital output depends on the reference voltage, layout, and the
exact timing of the external event. The error can change if the external event changes in time with respect to the
SCLK input.
With this in mind, power to the TSC2008 should be clean and well-bypassed. A 0.1
F ceramic bypass capacitor
should be placed as close to the device as possible. In addition, a 1
F to 10F capacitor may also be needed if
the impedance of the connection between VDD/REF and the power supply is high.
A bypass capacitor is generally not needed on the VDD/REF pin because the internal reference is buffered by an
internal op amp. If an external reference voltage originates from an op amp, make sure that it can drive any
bypass capacitor that is used without oscillation.
The TSC2008 architecture offers no inherent rejection of noise or voltage variation with regard to using an
external reference input, which is of particular concern when the reference input is tied to the power supply. Any
noise and ripple from the supply appear directly in the digital results. While high-frequency noise can be filtered
out, voltage variation as a result of line frequency (50Hz or 60Hz) can be difficult to remove. Some package
options have pins labeled as VOID. Avoid any active trace going under any pin marked as VOID unless it is
shielded by a ground or power plane.
The GND pin should be connected to a clean ground point. In many cases, this point is the analog ground. Avoid
connections that are too near the grounding point of a microcontroller or digital signal processor. If needed, run a
ground trace directly from the converter to the power-supply entry or battery connection point. The ideal layout
includes an analog ground plane dedicated to the converter and associated analog circuitry.
In the specific case of use with a resistive touch screen, care should be taken with the connection between the
converter and the touch screen. Because resistive touch screens have fairly low resistance, the interconnection
should be as short and robust as possible. Loose connections can be a source of error when the contact
resistance changes with flexing or vibrations.
As indicated previously, noise can be a major source of error in touch-screen applications (for example,
applications that require a back-lit LCD panel). This electromagnetic interference (EMI) noise can be coupled
through the LCD panel to the touch screen and cause flickering of the converted A/D converter data. Several
things can be done to reduce this error, such as using a touch screen with a bottom-side metal layer connected
to ground, which couples the majority of noise to ground. Additionally, filtering capacitors, from Y+, Y–, X+, and
X– to ground, can also help. Note, however, that the use of these capacitors increases screen settling time and
requires a longer time for panel voltages to stabilize. The resistor value varies depending on the touch screen
sensor used. The PENIRQ pull-up resistor (RIRQ) may be adequate for most of sensors. If not used, the
general-purpose analog input to the converter (AUX) should be connected to the analog ground plane.
Copyright 2008–2009, Texas Instruments Incorporated
31
Product Folder Link(s): TSC2008
相關PDF資料 |
PDF描述 |
|---|---|
| TSC2008IRGVT | SPECIALTY CONSUMER CIRCUIT, PQCC16 |
| TSC2008IYZGR | SPECIALTY CONSUMER CIRCUIT, BGA12 |
| TSC2008IYZGT | SPECIALTY CONSUMER CIRCUIT, BGA12 |
| TSC2008TRGVRQ1 | SPECIALTY CONSUMER CIRCUIT, PQCC16 |
| TSC2046EIPWG4 | SPECIALTY CONSUMER CIRCUIT, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSC2008IRGVT | 功能描述:觸摸屏轉換器和控制器 Nano-Pwr Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2008IYZGR | 功能描述:觸摸屏轉換器和控制器 Nano-Pwr Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2008IYZGT | 功能描述:觸摸屏轉換器和控制器 Nano-Pwr Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2008-Q1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.2V to 3.6V, 12-Bit, Nanopower, 4-Wire Micro TOUCH SCREEN CONTROLLER with SPIa?￠ |
| TSC2008RGVR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.2V to 3.6V, 12-Bit, Nanopower, 4-Wire Micro TOUCH SCREEN CONTROLLER with SPI? |
發布緊急采購，3分鐘左右您將得到回復。