- 您現在的位置：買賣IC網 > PDF目錄98302 > TSC2046EIPW (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PDSO16 PDF資料下載
參數資料
| 型號： | TSC2046EIPW |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO16 |
| 封裝： | GREEN, PLASTIC, TSSOP-16 |
| 文件頁數： | 7/32頁 |
| 文件大小： | 755K |
| 代理商： | TSC2046EIPW |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
TSC2046E
SBAS417B JUNE 2007 REVISED JANUARY 2008
www.ti.com
15
Control Byte
The control byte (on DIN), as shown in Table 3, provides
the
start
conversion,
addressing,
ADC
resolution,
configuration,
and power-down of the TSC2046E.
Figure 9, Table 3 and Table 4 give detailed information
regarding the order and description of these control bits
within the control byte.
Initiate START—The first bit, the S bit, must always be
high and initiates the start of the control byte. The
TSC2046E ignores inputs on the DIN pin until the start bit
is detected.
Addressing—The next three bits (A2, A1, and A0) select
the active input channel(s) of the input multiplexer (see
Table 1, Table 2, and Figure 2), touch screen drivers, and
the reference inputs.
MODE—The mode bit sets the resolution of the ADC. With
this bit low, the next conversion has 12-bit resolution,
whereas with this bit high, the next conversion has 8-bit
resolution.
SER/DFR—The SER/DFR bit controls the reference
mode, either single-ended (high) or differential (low). The
differential mode is also referred to as the ratiometric
conversion mode and is preferred for X-Position,
Y-Position,
and
Pressure-Touch
measurements
for
optimum performance. The reference is derived from the
voltage at the switch drivers, which is almost the same as
the voltage to the touch screen. In this case, a reference
voltage is not needed as the reference voltage to the ADC
is the voltage across the touch screen. In the single-ended
mode, the converter reference voltage is always the
difference between the VREF and GND pins (see Table 1
and Table 2, and Figure 2 through Figure 5, for further
information).
BIT 7
(MSB)
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
(LSB)
S
A2
A1
A0
MODE
SER/DFR
PD1
PD0
Table 3. Order of the Control Bits in the Control
Byte
BIT
NAME
DESCRIPTION
7
S
Start bit. Control byte starts with first high bit on DIN.
A new control byte can start every 15th clock cycle
in 12-bit conversion mode or every 11th clock cycle
in 8-bit conversion mode (see Figure 13).
6-4
A2-A0
Channel Select bits. Along with the SER/DFR bit,
these bits control the setting of the multiplexer input,
touch driver switches, and reference inputs (see
Table 1 and Figure 13).
3
MODE
12-Bit/8-Bit Conversion Select bit. This bit controls
the number of bits for the next conversion: 12-bits
(low) or 8-bits (high).
2
SER/DFR
Single-Ended/Differential Reference Select bit. Along
with bits A2-A0, this bit controls the setting of the
multiplexer input, touch driver switches, and
reference inputs (see Table 1 and Table 2).
1-0
PD1-PD0
Power-Down Mode Select bits. Refer to Table 5 for
details.
Table 4. Descriptions of the Control Bits within
the Control Byte
p
t
ACQ
Acquire
Idle
Conversion
Idle
1
DCLK
CS
81
11
DOUT
BUSY
Drivers 1 and 2
(1)
(SER/DFR High)
Drivers 1 and 2
(1, 2)
(SER/DFR Low)
(MSB)
(START)
(LSB)
A2
S
On
Off
DIN
A1
A0 MODE
SER/
DFR
PD1 PD0
10
987
65
4
3
2
1
0
Zero Filled...
81
8
(1) For YPosition, Driver 1 is on X+ is selected, and Driver 2 is off. For XPosition, Driver 1 is off, Y+ is selected, and Driver 2 is on. Y
will turn on
when powerdown mode is entered and PD0 = 0.
(2) Drivers will remain on if PD0 = 1 (no power down) until selected input channel, reference mode, or owerdown mode is changed, or CS is high.
NOTES:
Figure 9. Conversion Timing, 24 Clocks-per-Conversion, 8-Bit Bus Interface.
No DCLK delay required with dedicated serial port
相關PDF資料 |
PDF描述 |
|---|---|
| TSC2046EIZQCR | SPECIALTY CONSUMER CIRCUIT, PBGA48 |
| TSC2100IDARG4 | SPECIALTY CONSUMER CIRCUIT, PDSO32 |
| TSC2100IDAR | SPECIALTY CONSUMER CIRCUIT, PDSO32 |
| TSC2100IDA | SPECIALTY CONSUMER CIRCUIT, PDSO32 |
| TSC2100IRHBR | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSC2046EIPW | 制造商:Texas Instruments 功能描述:Controller IC 制造商:Texas Instruments 功能描述:CONTROLLER IC |
| TSC2046EIPWG4 | 功能描述:觸摸屏轉換器和控制器 4-Wire w/ Low Voltage Digital I/O RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2046EIPWR | 功能描述:觸摸屏轉換器和控制器 4-Wire Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2046EIPWRG4 | 功能描述:觸摸屏轉換器和控制器 4-Wire w/ Low Voltage Digital I/O RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2046EIRGVR | 功能描述:觸摸屏轉換器和控制器 4-Wire Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
發布緊急采購，3分鐘左右您將得到回復。