- 您現在的位置：買賣IC網 > PDF目錄98302 > TSC2100IDARG4 (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PDSO32 PDF資料下載
參數資料
| 型號： | TSC2100IDARG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO32 |
| 封裝： | GREEN, PLASTIC, TSSOP-32 |
| 文件頁數： | 13/76頁 |
| 文件大小： | 1143K |
| 代理商： | TSC2100IDARG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
TSC2100
SLAS378 NOVEMBER 2003
www.ti.com
20
Touch Detect/Data Available
The pen interrupt/data available (PINTDAV) output function is detailed in Figure 18. While in the power-down mode, the
Y– driver is ON and connected to AVSS and the X+ pin is connected through an on-chip pullup resistor to AVDD. In this
mode, the X+ pin is also connected to a digital buffer and mux to drive the PINTDAV output. When the panel is touched,
the X+ input is pulled to ground through the touch screen, and the peninterrupt signal goes LOW due to the current path
through the panel to AVSS, initiating an interrupt to the processor. During the measurement cycles for X and Y position,
the X+ input is disconnected from the pen-interrupt circuit to prevent any leakage current from the pullup resistor flowing
through the touch screen, and thus causing conversion errors.
Temp1
Temp2
Temp
Diode
DATAV
PINTDAV
High Except When
Temp1, Temp2 Activated
X+
Y+
Y
ON
50 k
Y+ or X+ Drivers On or
Temp1, Temp2
Measurements Activated
Figure 18. PINTDAV Functional Block Diagram
In modes where the TSC2100 needs to detect if the screen is still touched (for example, when doing a PINTDAV initiated
X, Y, and Z conversion), the TSC2100 must reset the drivers so that the 50-k resistor is connected. Because of the high
value of this pullup resistor, any capacitance on the touch screen inputs causes a long delay time, and may prevent the
detection from occurring correctly. To prevent this, the TSC2100 has a circuit that allows any screen capacitance to be
precharged, so that the pullup resistor does not have to be the only source for the charging current. The time allowed for
this precharge, as well as the time needed to sense if the screen is still touched, can be set in the configuration control
register D5D0 of REG05H/Page1.
This does point out, however, the need to use the minimum capacitor values possible on the touch screen inputs. These
capacitors may be needed to reduce noise, but too large a value increases the needed precharge and sense times, as well
as panel voltage stabilization time.
The function of PINTDAV output is programmable and controlled by writing to the bits D15D14 of REG 01H/Page1 as
described in the Table 2.
Table 2. Programmable PINTDAV Functionality
D15D14
PINTDAV FUNCTION
00
Acts as PEN interrupt (active low) only. When PEN touch is detected, PINTDAV goes low.
01
Acts as data available (active low) only. The PINTDAV goes low as soon as one set of ADC conversions are completed for data
of X,Y, XYZ, battery input, or auxiliary input selected by D13D10 in REG00H/Page1. The resulting A/D output is stored in the
appropriate registers. The PINTDAV remains low and goes high only after this complete set of registers selected by D13D10
REG00H/Page1 is read out.
10
11
Acts as both PEN interrupt and data available. When PEN touch is detected, PINTDAV goes low and remains low. The PINTDAV
goes high only after one set of A/D conversions is completed for data of X,Y, XYZ, battery input, or auxiliary input selected by
D13D10 in REG00H/Page1.
NOTE: See the section Conversion Time Calculation for the TSC2100 in this data sheet for the timing diagrams.
Pen-touch detect circuit is disabled during hardware power down.
相關PDF資料 |
PDF描述 |
|---|---|
| TSC2100IDAR | SPECIALTY CONSUMER CIRCUIT, PDSO32 |
| TSC2100IDA | SPECIALTY CONSUMER CIRCUIT, PDSO32 |
| TSC2100IRHBR | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| TSC2100IRHB | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| TSC2100IDAG4 | SPECIALTY CONSUMER CIRCUIT, PDSO32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSC2100IRHB | 功能描述:觸摸屏轉換器和控制器 Prog 4-Wire w/Ster Codec & Hdph/Spk Amp RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2100IRHBG4 | 功能描述:觸摸屏轉換器和控制器 Prog 4-Wire w/Ster Codec & Hdph/Spk Amp RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2100IRHBR | 功能描述:觸摸屏轉換器和控制器 Prog 4-Wire w/Ster Codec & Hdph/Spk Amp RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2100IRHBRG4 | 功能描述:觸摸屏轉換器和控制器 Prog 4-Wire w/Ster Codec & Hdph/Spk Amp RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2100IRHBRMULT1 | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。