- 您現在的位置：買賣IC網 > PDF目錄98302 > TSC2300IPAG (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQFP64 PDF資料下載
參數資料
| 型號： | TSC2300IPAG |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| 封裝： | GREEN, PLASTIC, TQFP-64 |
| 文件頁數： | 60/81頁 |
| 文件大小： | 1039K |
| 代理商： | TSC2300IPAG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
www.ti.com
N0 ) 2 N1 Z–1 ) N2 Z–2
32768–2 D1 Z–1–D2 Z–2
N3 ) 2 N4 Z–1 ) N5 Z–2
32768–2 D4 Z–1–D5 Z–2
(12)
TSC2300
SLAS372 — NOVEMBER 2002
Conventional audio DAC designs utilize high-order analog filtering to remove quantization noise that falls within the
audio band when operating at low sample rates. Here, however, the increased oversampling at low sample rates keeps
the noise above 20 kHz, yielding a similar noise floor out to 20 kHz whether the sample rate is 8 kHz or 48 kHz. If the
audio bypass path is not in use when the stereo DAC is in use, the user should power down the bypass path, as this
improves DAC SNR and reduces power consumption.
In addition, the digital interpolation filter provides enhanced image filtering to reduce signal images caused by the
upsampling process that land below 20 kHz. For example, upsampling an 8-kHz signal produces signal images at
multiples of 8 kHz, i.e., 8 kHz, 16 kHz, 24 kHz, etc. The images at 8 kHz and 16 kHz are below 20 kHz and thus are
still audible to the listener, therefore they must be filtered heavily to maintain a good quality output. The interpolation
filter is designed to maintain at least 65-dB rejection of signal images landing between 0.55 Fs and 3.5 Fs, for all
sample rates, including any images that land within the audio band (20 Hz-20 kHz). Passband ripple for all sample-rate
cases (from 20 Hz to 0.4535 Fs) is +/-0.1-dB maximum.
The analog reconstruction filter design consists of a switched-capacitor filter with one pole and three zeros. The
single-bit data operates at 128 x 48 kHz = 6.144 MHz (for selected sample-rates that are submultiples of 48 kHz) or at
128 x 44.1 kHz = 5.6448 MHz (for selected sample-rates that are submultiples of 44.1 kHz). The interpolation filter
takes data at the selected sample-rate from the effects processing block, then performs upsampling and image filtering,
yielding a 6.144-MHz or 5.6448-MHz data stream, which is provided to the digital delta-sigma modulator.
Audio DAC SNR performance is 98-dB-A typical over 20 Hz - 20 kHz bandwidth in 44.1/48-kHz mode at the
line-outputs with a 3.3-V supply level.
DAC Digital De-emphasis
The DAC digital effects processing block can perform several operations on the audio data before it is passed to the
interpolation filter. One such operation is a digital de-emphasis, which can be enabled or disabled by the user via the
DEEMP bit (Bit 0, Reg 05h, Pg 2). This is only available for sample rates of 32 kHz, 44.1 kHz, and 48 kHz. The
transfer function consists of a pole with time constant of 50 sec and a zero with time constant of 15 sec.
DAC Programmable Digital Effects Filter
The DAC digital effects processing block also includes a fourth order digital IIR filter with programmable coefficients
(independently programmable per channel). The filter transfer function is given by:
The N and D coefficients are set via SPI registers, and this filter can be enabled or disabled via the BASS bit (Bit 1,
Reg 05h, Pg ú2). This functionality can implement a number of different functions, such as bass-boost (default),
treble-boost, mid-boost, or other equalization. This transfer function(s) can be determined by the user and loaded to
the TSC2300 at power-up, and the feature can then be switched on or off by the user during normal operation.
The default coefficients at reset are given by:
N0=N3=27618
D1=D4=32130
N1=N4=-27033
D2=D5=-31505
N2=N5=26461
which implements the bass-boost transfer function shown in Figure 77, having a 3-dB attenuation for signals above
approximately 150 Hz when operating at a 48-kHz sampling rate. All coefficients are represented by 16-bit twos
complement integers with values ranging from -32768 to +32767.
63
相關PDF資料 |
PDF描述 |
|---|---|
| TSC2300IPAGRG4 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TSC2301IPAGR | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TSC2301IPAG | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TSC2301IGQZR | SPECIALTY CONSUMER CIRCUIT, PBGA120 |
| TSC2301IGQZ | SPECIALTY CONSUMER CIRCUIT, PBGA120 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSC2300IPAGG4 | 功能描述:觸摸屏轉換器和控制器 SMART 4-Wire with Audio RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2300IPAGR | 功能描述:觸摸屏轉換器和控制器 20-Bit 48-Ksps I2S Audio Codec RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2300IPAGRG4 | 功能描述:觸摸屏轉換器和控制器 20-Bit 48-Ksps I2S Audio Codec RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| TSC2301 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH STEREO AUDIO CODEC |
| TSC2301EVM | 功能描述:觸摸傳感器開發工具 TSC2301 Eval Mod RoHS:否 制造商:Cypress Semiconductor 工具用于評估: 接口類型: 工作電壓: 最大工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。