- 您現在的位置：買賣IC網 > PDF目錄365975 > TSC87C52-33CBB CMOS 0 to 33 MHz Programmable 8朾it Microcontroller PDF資料下載
參數資料
| 型號： | TSC87C52-33CBB |
| 英文描述： | CMOS 0 to 33 MHz Programmable 8朾it Microcontroller |
| 中文描述： | 的CMOS 0至33 MHz的可編程微控制器8朾它 |
| 文件頁數： | 10/24頁 |
| 文件大小： | 273K |
| 代理商： | TSC87C52-33CBB |
TSC87C52
10
Rev. C – 10 Sept 1997
Preliminary
MATRA MHS
Programmable Clock Output
A 50% duty cycle clock can be programmed to come out on P1.0. This pin, besides being a regular I/O pin, has two
alternate functions. It can be programmed to input external clock for Timer/Counter 2 or to output a 50% duty cycle
clock from frequency fosc/2
18
to frequency fosc/4 (61 Hz to 4 MHz at a 16 MHz operating frequency).
The clock–out frequency depends on the oscillator frequency and the reload value of Timer 2 capture registers
RCAP2H and RCAP2L as shown in this equation:
Oscillator frequency
Clock–Out frequency=4
(65536 – RCAP2H,RCAP2L)
To configure the Timer/Counter 2 as a clock generator, bit C/T2 in T2CON (bit location 1) must be cleared and bit T2OE
must be set. Bit TR2 in T2CON starts and stops the timer (see Figure 7). T2OE is located in T2MOD at bit location
1 (see Table 5).
In the clock–out mode, Timer 2 roll–overs will not generate an interrupt. This is similar to when Timer 2 is used as
a baud–rate generator. It is possible to use Timer 2 as a baud–rate generator and as clock generator simultaneously.
Note however, that the baud–rate and clock–out frequencies can not be determined independently from one another
since they both use RCAP2H and RCAP2L.
TR2
÷
2
OSC
OVERFLOW
T2EX
EXF2
TH2
(8–bit)
TL2
(8–bit)
TIMER 2
INTERRUPT
EXEN2
RCAP2H
(8–bit)
RCAP2L
(8–bit)
T2OE
C/T2
T2
÷
2
Figure 7 Timer 2 Clock–Out Mode
Table 5 T2MOD – Timer 2 Control Register (C9h)
7
6
5
4
3
2
1
0
–
–
–
–
–
–
T2OE
DCEN
Symbol
Description
–
Reserved
Do not write 1 in these bits.
T2OE
Timer 2 Output Enable bit
Set to program P1.0/T2 as clock output.
Clear to program P1.0/T2 as clock input or I/O port.
DCEN
Decrement Enable bit
Set to enable Timer 2 as up/down counter.
Clear to disable Timer 2 as up/down counter.
The reset value of T2MOD is XXXX XX00b.
相關PDF資料 |
PDF描述 |
|---|---|
| TSC87C52-33CBD | CMOS 0 to 33 MHz Programmable 8朾it Microcontroller |
| TSC87C52-33CBR | CMOS 0 to 33 MHz Programmable 8朾it Microcontroller |
| TSC87C52-33CJB | CMOS 0 to 33 MHz Programmable 8朾it Microcontroller |
| TSC87C52-33CJD | CMOS 0 to 33 MHz Programmable 8朾it Microcontroller |
| TSC87C52-33CJR | CMOS 0 to 33 MHz Programmable 8朾it Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSC888AILT | 功能描述:電流靈敏放大器 Sense Amplifier 20 Gain RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| TSC888BILT | 功能描述:電流靈敏放大器 Sense Amplifier 50 Gain RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| TSC888CILT | 功能描述:電流靈敏放大器 Sense Amplifier 100 Gain RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| TSC9 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EURO TERMINAL BLOCKS |
| TSC903 | 制造商:Laird Technologies Inc 功能描述:CLIP TO-3P 制造商:Laird Technologies Inc 功能描述:CLIP, TO-3P 制造商:Laird Technologies Inc 功能描述:CLIP, TO-3P; External Width:6.5mm; SVHC:No SVHC (18-Jun-2012); Isolation Voltage:1kV; Length:30mm; Material:Steel; Package / Case:TO-3P, TO-218, TO-247; Packages Cooled:TO-3P, TO-218, TO-247; Pad Thickness Max:0.5mm; Panel Thickness ;RoHS Compliant: Yes 制造商:Laird Technologies Inc 功能描述:CLIP, TO-3P; External Width:6.5mm; SVHC:No SVHC (18-Jun-2012); Isolation Voltage:1kV; Length:30mm; Material:Steel; Package / Case:TO-3P, TO-218, TO-247; Packages Cooled:TO-218, TO-247, TO-3P; Pad Thickness Max:0.5mm; Panel Thickness ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。