- 您現在的位置：買賣IC網 > PDF目錄382701 > TZA3041 (NXP Semiconductors N.V.) Gigabit Ethernet/Fibre Channel laser drivers PDF資料下載
參數資料
| 型號： | TZA3041 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Gigabit Ethernet/Fibre Channel laser drivers |
| 中文描述： | 千兆以太網/光纖通道激光驅動器 |
| 文件頁數： | 10/32頁 |
| 文件大小： | 153K |
| 代理商： | TZA3041 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
2002 Aug 13
10
Philips Semiconductors
Product specification
Gigabit Ethernet/Fibre Channel laser
drivers
TZA3041AHL; TZA3041BHL;
TZA3041U
Automatic laser shut-down and laser slow start
The laser modulation and bias currents can be rapidly
switched off when a HIGH level (CMOS) is applied to
pin ALS. This function allows the circuit to be shut-down in
the event of an optical system malfunction. A 25 k
pull-down resistor defaults pin ALS to the non active state
(see Fig.11).
When a LOW level is applied to pin ALS, the modulation
and bias currents slowly increase to the desired values at
the typical time constants of
τ
ONE
and
τ
ZERO
, respectively.
This can be used to slow-start the laser.
Manual laser override
The automatic laser control function can be overridden by
connecting voltage sources to pins TZERO and TONE to
take direct control of the current sources for bias and
modulation respectively. The control voltages should
range from 1.4 to 3.4 V to swing the modulation current
over the range 1 to 60 mA and the bias current over the
range 1 to 90 mA. These current ranges are guaranteed.
Due to the tolerance range in the manufacturing process,
some devices may have higher current values than those
specified, as shown in Figs 12 and 13. Both figures show
that temperature changes cause a slight tilting of the linear
characteristic around an input voltage of 2.4 V.
Consequently, the manually controlled current level is
most insensitive to temperature variations at around this
value. Bias and modulation currents in excess of the
specified range are not supported and should be avoided.
Currentsintoor outof pins TZERO and TONEin excess of
10
μ
A must be avoided to prevent damage to the circuit.
handbook, halfpage
MGS905
GND
40 pF
<
1 nA
LINEAR VOLTAGE TO
CURRENT CONVERTER
2.4 V
<
1 nA
Fig.10 TZERO and TONE internal configuration.
handbook, halfpage
MGS911
25 k
VCC(R)
100
GND
ALS
100
Fig.11 ALS input.
相關PDF資料 |
PDF描述 |
|---|---|
| TZA3041BHL | Gigabit Ethernet/Fibre Channel laser drivers |
| TZA3041U | Gigabit Ethernet/Fibre Channel laser drivers |
| U-30-WCAB | High speed dual comparators |
| U-60-PP | Low power quad operational amplifiers |
| U05GU4B48 | SILICON DIFFUSED JUNCTION TYPE RECTIFIER STACK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TZA3041AHL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Gigabit Ethernet/Fibre Channel laser drivers |
| TZA3041BHL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Gigabit Ethernet/Fibre Channel laser drivers |
| TZA3041U | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Gigabit Ethernet/Fibre Channel laser drivers |
| TZA3043 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Gigabit Ethernet/Fibre Channel transimpedance amplifier |
| TZA3043B | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Gigabit Ethernet/Fibre Channel transimpedance amplifier |
發布緊急采購，3分鐘左右您將得到回復。