- 您現在的位置：買賣IC網 > PDF目錄382702 > U210B Phase Control Circuit - Load Current Feedback Applications PDF資料下載
參數資料
| 型號： | U210B |
| 英文描述： | Phase Control Circuit - Load Current Feedback Applications |
| 中文描述： | 相位控制電路-負載電流反饋的應用 |
| 文件頁數： | 4/15頁 |
| 文件大小： | 378K |
| 代理商： | U210B |
TELEFUNKEN Semiconductors
U 210 B / U 210 B–FP
4
Preliminary Information
Soft–start
As soon as the supply voltage builds up (t
1
), the integrated soft–start is initiated. The figure below shows the behaviour
of the voltage across the soft–start capacitor and is identical with the voltage on the phase control input on Pin 9. This
behaviour allows a gentle start–up for the motor.
Figure 4 Soft–start
C
3
is first charged with typ. 30 A. The charging current then increases as the voltage across C
4
increases giving a
progressively rising charging function with more and more strongly accelerates the motor with increasing rotational
speed. The charging function determines the acceleration up to the set point. The charging current can have a maximum
value of 85 A.
Control amplifier
The integrated control amplifier with differential input has a bipolar current output, with typically
±
110 A at Pin 9 and
a transmittance of typ. 1000 A/V. The amplification and frequency response are determined by external circuit. For
operation as a power control, it should be connected with Pin 7. Phase angle of the firing pulse can be adjusted by using
the voltage at Pin 8. An internal limiting circuit prevents the voltage on Pin 9 becoming more negative than V
13
+ 1 V.
Load current detection, Figure 2
Voltage drop across R
8
, dependent of load current, generates an input–current at Pin 11 limited by R
5
. Proportional output
current of 0.44 x I
11
(CTR) is available at Pin 12. It is proportional with respect to phase and amplitude of load current.
Capacitor C
3
integrates the current whereas resistor R
7
evaluates it. The voltage obtained due to load current
proportionality, can be used according to the application i.e., load current compensation or load current regulation.
Pulse output stage
The pulse output stage is short circuit protected and can typically deliver currents of 125 mA. For the design of smaller
triggering currents, the function I
GT
= f (R
GT
) has been given in the data sheets in the appendix. In contrast to the U 111 B
and the TEA 1007, the pulse output stage of the U 210 B has no gate bypass resistor.
Automatic retriggering
The automatic retriggering prevents half cycles without current flow, even if the triac is turned off earlier e.g. due to not
exactly centred collector (brush lifter) or in the event of unsuccessful triggering. After a time lapse of t
pp
=4.5 t
p
is
generated another triggering pulse which is repeated until either the triac fires or the half cycle finishes.
相關PDF資料 |
PDF描述 |
|---|---|
| U210B-FP | Phase Control Circuit - Load Current Feedback Applications |
| U211B | Phase Control Circuit - General Purpose Feedback |
| U211B2 | Phase Control Circuit - General Purpose Feedback |
| U211B3 | Phase Control Circuit - General Purpose Feedback |
| U2270B | Read / Write Base Station IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| U210B1 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:Phase Control Circuit Load Current Feedback Applications |
| U210B-FP | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:Phase Control Circuit - Load Current Feedback Applications |
| U211004 | 制造商:LAPP OLFLEX 功能描述:Tray Cable, OLFLEX TC 600, Multiconductor VNTC, 10/4c, UL TC-ER, CSA, CE, 600V |
| U211204 | 制造商:LAPP OLFLEX 功能描述:Tray Cable, OLFLEX TC 600, Multiconductor VNTC, 12/4c, UL TC-ER, CSA, CE, 600V |
| U211205 | 制造商:LAPP OLFLEX 功能描述:Tray Cable, OLFLEX TC 600, Multiconductor VNTC, 12/5c, UL TC-ER, CSA, CE, 600V |
發布緊急采購，3分鐘左右您將得到回復。