- 您現在的位置：買賣IC網 > PDF目錄382702 > U211B3 Phase Control Circuit - General Purpose Feedback PDF資料下載
參數資料
| 型號： | U211B3 |
| 英文描述： | Phase Control Circuit - General Purpose Feedback |
| 中文描述： | 相位控制電路-通用信息反饋 |
| 文件頁數： | 5/20頁 |
| 文件大小： | 322K |
| 代理商： | U211B3 |
U211B2/ B3
TELEFUNKEN Semiconductors
Rev. A1, 29-May-96
5 (20)
C = 1 F
10 V
95 10363
18
17
16
15
1
2
3
4
R = 1 M
Figure 5. Operation delay
Control Amplifier (Figure 2)
The integrated control amplifier with differential input
compares the set value (Pin 11) with the instantaneous
value on Pin 10 and generates a regulating voltage on the
output Pin 12 (together with the external circuitry on
Pin 12) which always tries to hold the actual voltage at the
value of the set voltages. The amplifier has a
transmittance of typically 1000 A/V and a bipolar
current source output on Pin 12 which operates with
typically
±
110 A. The amplification and frequency
response are determined by R
7
, C
7
, C
8
and R
11
(can be left
out). For open loop operation, C
4
, C
5
, R
6
, R
7
, C
7
, C
8
and
R
11
can be omitted. Pin 10 should be connected with
Pin 12 and Pin 8 with Pin 2. The phase angle of the
triggering pulse can be adjusted using the voltage on
Pin 11. An internal limitation circuit prevents the voltage
on Pin 12 from becoming more negative than V
16
+ 1 V.
Load Limitation
The load limitation, with standard circuitry, provides
absolute protection against overloading of the motor. the
function of the load limiting takes account of the fact that
motors operating at higher speeds can safely withstand
large power dissipations than at lower speeds due to the
increased action of the cooling fan. Similary, consider-
ations have been made for short term overloads for the
motor which are, in practice, often required. These
finctions are not damaging and can be tolerated.
In each positive half-cycle, the circuit measures via R
10
the load current on Pin 14 as a potential drop across R
8
and produces a current proportional to the voltage on
Pin 14. This current is available on Pin 15 and is
integrated by C
9
. If, following high current amplitudes or
a large phase angle for current flow, the voltage on C
9
exceeds an internally set threshold of approx. 7.3 V
(reference voltage Pin 16) then a latch is set and the load
limiting is turned on. A current source (sink) controlled
by the control voltage on Pin 15 now draws current from
Pin 12 and lowers the control voltage on Pin 12 so that the
phase angle
is increased to
max
.
The simultaneous reduction of the phase angle during
which current flows causes firstly: a reduction of the
rotational speed of the motor which can even drop to zero
if the angular momentum of the motor is excessively
large, and secondly: a reduction of the potential on C
9
which in turn reduces the influence of the current sink on
Pin 12. The control voltage can then increase again and
bring down the phase angle. This cycle of action sets up
a “balanced condition” between the “current integral” on
Pin 15 and the control voltage on Pin 12.
Apart from the amplitude of the load current and the time
during which current flows, the potential on Pin 12 and
hence the rotational speed also affects the function of the
load limiting. A current proportional to the potential on
Pin 10 gives rise to a voltage drop across R
10
, via Pin 14,
so that the current measured on Pin 14 is smaller than the
actual current through R
8
.
This means that higher rotational speeds and higher
current amplitudes lead to the same current integral.
Therefore, at higher speeds, the power dissipation must
be greater than that at lower speeds before the internal
threshold voltage on Pin 15 is exceeded. The effect of
speed on the maximum power is determined by the
resistor R
10
and can therefore be adjusted to suit each
individual application.
If, after the load limiting has been turned on, the
momentum of the load sinks below the “o-momentum”
set using R
10
, then V
15
will be reduced. V
12
can then in-
crease again so that the phase angle is reduced. A smaller
phase angel corresponds to a larger momentum of the mo-
tor and hence the motor runs up - as long as this is allowed
by the load momentum. For an already rotating machine,
the effect of rotation on the measured “current integral”
ensures that the power dissipation is able to increase with
the rotational speed. the result is: a current controlled
accelleration run-up., which ends in a small peak of accel-
leraton when the set point is reached. The latch of the load
limiting is simultaneously reset. The speed of the motor
is then again under control and it is capable of carrying its
full load. The above mentioned peak of accelleration
depends upon the ripple of actual speed voltage. A large
amount of ripple also leads to a large peak of
accelleration.
The measuring resistor R
8
should have a value which
ensures that the amplitude of the voltage across it does not
exceed 600 mV.
相關PDF資料 |
PDF描述 |
|---|---|
| U2270B | Read / Write Base Station IC |
| U2305B | VHF/ UHF-Tuner-IC |
| U2305B-AFSG3 | VHF/ UHF-Tuner-IC |
| U2320B | VHF/UHF Tuner-IC |
| U2320B-FLG3 | VHF/UHF Tuner-IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| U211B-M | 功能描述:IC PHASE CONTROL TACHO 18-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 產品變化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 標準包裝:1 系列:- 應用:DC 電機控制器，無刷（BLDC），3 相 評估套件:可供 輸出數:1 電流 - 輸出:100mA 電壓 - 負載:5.25 V ~ 20 V 電源電壓:5.25 V ~ 20 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-VQFN（7x7） 包裝:剪切帶 (CT) 其它名稱:ATA6833-PLQWCT |
| U211B-MFP | 功能描述:IC PHASE CONTROL TACHO 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 產品變化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 標準包裝:1 系列:- 應用:DC 電機控制器，無刷（BLDC），3 相 評估套件:可供 輸出數:1 電流 - 輸出:100mA 電壓 - 負載:5.25 V ~ 20 V 電源電壓:5.25 V ~ 20 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-VQFN（7x7） 包裝:剪切帶 (CT) 其它名稱:ATA6833-PLQWCT |
| U211B-MFPG3 | 功能描述:IC PHASE CONTROL TACHO 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| U211B-MFPG3Y | 功能描述:馬達/運動/點火控制器和驅動器 Phase Sw/Control w/ Tacho overld limit RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| U211B-MFPY | 功能描述:馬達/運動/點火控制器和驅動器 Phase Sw/Control w/ Tacho overld limit RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。