- 您現在的位置：買賣IC網 > PDF目錄382716 > UBA1710M (NXP SEMICONDUCTORS) Modulator for GaAs power amplifiers(應用于GaAs功率放大器的調節器) PDF資料下載
參數資料
| 型號： | UBA1710M |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Modulator for GaAs power amplifiers(應用于GaAs功率放大器的調節器) |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封裝： | 4.4MM, PLASTIC, SOT-266, SSOP-20 |
| 文件頁數： | 8/12頁 |
| 文件大小： | 73K |
| 代理商： | UBA1710M |
1997 Oct 17
8
Philips Semiconductors
Product specification
Modulator for GaAs power amplifiers
UBA1710M
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook”(order code 9398 652 90011).
Reflow soldering
Reflow soldering techniques are suitable for all SSOP
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250
°
C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45
°
C.
Wave soldering
Wave soldering is
not
recommended for SSOP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
If wave soldering cannot be avoided, the following
conditions must be observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
The longitudinal axis of the package footprint must
be parallel to the solder flow and must incorporate
solder thieves at the downstream end.
Even with these conditions, only consider wave
soldering SSOP packages that have a body width of
4.4 mm, that is SSOP16 (SOT369-1) or
SSOP20 (SOT266-1)
.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within
6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°
C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| UBA2000T | Electronic TL-lamp starter(電子TL-lamp啟動器) |
| UBA2030T | Full bridge driver IC(整橋驅動器芯片) |
| UBA2050 | One-chip telephone ICs with speech, dialler and ringer functions(帶語音，撥號及振鈴功能的單片電話芯片) |
| UBA2050A | One-chip telephone ICs with speech, dialler and ringer functions(帶語音，撥號及振鈴功能的單片電話芯片) |
| UBA2051 | One-chip telephone ICs with speech, dialler and ringer functions |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UBA2000T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Electronic TL-lamp starter |
| UBA2007 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Charge switch |
| UBA2007TK/N2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Charge switch |
| UBA2008 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:脈沖模式智能充電開關 |
| UBA2013T/N3,518 | 功能描述:顯示驅動器和控制器 IC CONTROL BALLAST RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。