- 您現在的位置：買賣IC網 > PDF目錄382717 > UC2584N ISO HIGH SIDE SMART POWER SOLID STATE RELAY PDF資料下載
參數資料
| 型號： | UC2584N |
| 英文描述： | ISO HIGH SIDE SMART POWER SOLID STATE RELAY |
| 中文描述： | 模擬IC |
| 文件頁數： | 6/7頁 |
| 文件大小： | 180K |
| 代理商： | UC2584N |
6
UC1584
UC2584
UNITRODE CORPORATION
7 CONTINENTAL BLVD. MERRIMACK, NH 03054
TEL. (603) 424-2410 FAX (603) 424-3460
the driver during the on-time of the switch. Charge is be-
ing replenished to the bootstrap capacitor during the
off-time of the switch through the bootstrap diode con-
nected between VCC and VFLT as shown in the typical
application diagram.
Soft Start
The UC3584 Soft Start circuitry is designed to implement
closed loop startup of the power supply output. During
Soft Start, the reference to the noninverting input of the
error amplifier is controlled by the voltage across the soft
start capacitor on SS. As this voltage rises, it provides an
increasing reference to the error amplifier. Once the soft
start capacitor charges above the 1.5V precision refer-
ence of the error amplifier, SS gets disconnected from
the noninverting input of the error amplifier. This tech-
nique allows the error amplifier to stay in its linear mode
and to regulate the output voltage of the power supply
according to the gradually increasing reference voltage
on its noninverting input. Further advantage of the closed
loop start up scheme is the absence of output voltage
overshoot during power up of the power supply output.
Fault Detection
Fault Detection feature is implemented to detect exces-
sive overload conditions. Under these conditions the er-
ror amplifier output goes high to command the maximum
duty cycle. As soon as the error amplifier’s output ex-
ceeds 5V, the fault delay capacitor connected to the
CDLY pin starts charging. If C
DLY
capacitor voltage
reaches 2V before the error amplifier output falls back
below 5V, a fault condition is declared, the PWM output
is disabled and soft start cycle is initiated. Under persis-
tent fault conditions the UC3584 will continuously cycle
through soft start sequence, attempting to bring the out-
put to its regulated, nominal voltage. The value of C
DLY
capacitor should be chosen large enough to delay the
activation of the fault sequence in case of load transients
which can also cause the error amplifier output to go
high temporarily.
Error Amplifier
The Error Amplifier of the UC3584 is used to regulate the
voltage of an auxiliary output in a power supply. The
noninverting input of the error amplifier is connected to
an internal, 1.5V reference. The inverting input (FB pin)
is tied to an output voltage divider. The compensation
network of the negative feedback loop is connected be-
tween the amplifier’s output (COMP pin) and FB. The
noninverting input of the error amplifier is also connected
to the SS node through a diode. This arrangement allows
closed loop soft start for the output of a power supply
regulated by the UC3584. Closed loop soft start assures
that the error amplifier is kept in active mode and the out-
put voltage of the converter follows the reference voltage
on its noninverting input as it ramps up (following the SS
node). If a fault condition is detected, SS node gets
pulled to ground, forcing the error amplifier’s reference
low. Consequently, the error amplifier’s output voltage
goes low and duty cycle is reduced.
APPLICATION INFORMATION (cont.)
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| UC1584J | 8-bit MCU for automotive with Flash or ROM, 10-bit ADC, 5 timers, SPI, LINSCI", active CAN |
| UC2610DW | BRIDGE/RING DIODE ARRAY|SO |
| UC2610DWTR | High side smart power solid state relay |
| UC2610J | High side smart power solid state relay |
| UC2610N | BRIDGE/RING DIODE ARRAY|SO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UC2-5NJ | 功能描述:低信號繼電器 - PCB DPDT NL 5VDC RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
| UC2-5NU | 制造商:IMO Precision Controls Ltd 功能描述:RELAY DPCO 5V 制造商:NEC Electronics Corporation 功能描述:SIGNAL RELAY DPDT 5VDC 1A THROUGH HOLE 制造商:IMO PRECISION CONTROLS 功能描述:RELAY, DPCO, 5V 制造商:NEC Electronics Corporation 功能描述:SIGNAL RELAY DPDT 5VDC, 1A, THROUGH HOLE 制造商:IMO Precision Controls Ltd 功能描述:RELAY, DPCO, 5V; Coil Type:DC; Contact Configuration:DPCO; Contact Current Max:1A; Contact Voltage AC Nom:250V; Contact Voltage DC Nom:220V; Coil Voltage VDC Nom:5V; Coil Resistance:178ohm; Coil Power Cont:140mW; Relay ;RoHS Compliant: Yes 制造商:NEC Electronics Corporation 功能描述:SIGNAL RELAY DPDT 5VDC, 1A, THROUGH HOLE; Coil Type:DC; Contact Configuration:DPDT; Contact Current Max:1A; Contact Voltage AC Nom:125V; Contact Voltage DC Nom:30V; Coil Voltage VDC Nom:5V; Coil Resistance:178ohm ;RoHS Compliant: Yes 制造商:World Products 功能描述:Electromechanical Relay DPDT 1A 5VDC 178Ohm Through Hole |
| UC2-5NU | 制造商:IMO Precision Controls Ltd 功能描述:RELAY DPCO 5V |
| UC2-5SNJ | 功能描述:低信號繼電器 - PCB DPDT SNGL COIL 5VDC RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
| UC26 | 制造商:Greenlee Textron Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。