欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： UCB1300BE
廠商： NXP SEMICONDUCTORS
元件分類： 調制器/解調器
英文描述： Advanced modem/audio analog front-end
中文描述： MODEM-SUPPORT CIRCUIT, PQFP48
封裝： 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, SOT-313-2, LQFP-48
文件頁數： 54/56頁
文件大小： 1022K
代理商： UCB1300BE
1999 Jul 20
54
Philips Semiconductors
Preliminary specification
Advanced modem/audio analog front-end
UCB1300
SOLDERING
Introduction
There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and
surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for
surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often
used.
This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our
“IC Package Databook”(order code 9398 652 90011).
Reflow soldering
Reflow soldering techniques are suitable for all LQFP packages.
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the
printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between
50 and 300 seconds depending on heating method. Typical reflow temperatures range from 215 to 250
°
C.
Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45
°
C.
Wave soldering
Wave soldering is
not
recommended for LQFP packages. This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete solder penetration in multi-lead devices.
If wave soldering cannot be avoided, the following conditions must be observed:
A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering
technique should be used.
The footprint must be at an angle of 45
°
to the board direction and must incorporate solder thieves
downstream and at the side corners.
Even with these conditions, do not consider wave soldering LQFP packages LQFP48 (SOT313-2),
LQFP64 (SOT314-2) or LQFP80 (SOT315-1).
During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within 6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonally- opposite end leads. Use only a low voltage soldering iron (less
than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300
°
C. When using a
dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320
°
C.
相關PDF資料
PDF描述
UCB1400BE Audio codec with touch screen controller and power management monitor
UCB1400 Audio codec with touch screen controller and power management monitor
UCB1500 PCI to AC97 bridge/host controller
UCC1913D Very low drop voltage regulators with inhibit
UCC1913DTR Analog IC
相關代理商/技術參數
參數描述
UCB1400 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Audio codec with touch screen controller and power management monitor
UCB1400BE 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Audio codec with touch screen controller and power management monitor
UCB1400BE,128 功能描述:接口—CODEC AUDIO CODEC WITH TOUCHSCREEN RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
UCB1400BE,151 功能描述:接口—CODEC AUDIO CODEC RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
UCB1400BE,157 功能描述:接口—CODEC DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 鹤壁市| 屯门区| 革吉县| 方城县| 墨竹工卡县| 南昌县| 隆尧县| 沙湾县| 德兴市| 论坛| 长沙县| 彭水| 大埔区| 牡丹江市| 平武县| 通城县| 玉林市| 苗栗市| 安国市| 玉田县| 金门县| 洪湖市| 宜丰县| 湘乡市| 内乡县| 肇庆市| 上思县| 东台市| 钟祥市| 杭锦旗| 安新县| 广元市| 扬中市| 旬阳县| 仁布县| 乐清市| 冕宁县| 汝城县| 杂多县| 邹平县| 达日县|