- 您現在的位置：買賣IC網 > PDF目錄382729 > UZZ9000 (NXP SEMICONDUCTORS) Sensor Conditioning Electronic(傳感器調節芯片) PDF資料下載
參數資料
| 型號： | UZZ9000 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Sensor Conditioning Electronic(傳感器調節芯片) |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO24 |
| 封裝： | SO-24 |
| 文件頁數： | 8/16頁 |
| 文件大小： | 69K |
| 代理商： | UZZ9000 |
2000 May 19
8
Philips Semiconductors
Preliminary specification
Sensor Conditioning Electronic
UZZ9000
Trim interface
The serial interface used to switch the UZZ9000 into trim
mode consists of the two terminals SMODE (pin 10) and
DATA_CLK (pin 9). The structure of this protocol is shown
in Fig.4.
All signal levels at DATA_CLK and SMODE must be
selected according to the requirements listed in Table 3.
The following points must be taken into account with
regard to the asynchronous protocol.
The protocol starts with a falling edge at the SMODE,
whichmustoccuratahighDATA_CLKlevel.Thefollowing
five bits are used to code the message sent to the
UZZ9000. They are transferred via the SMODE and are
sampledwiththerisingedgeoftheDATA_CLK.Duringthe
fifthhighleveloutputofDATA_CLK(countedfromthestart
condition onwards), a rising edge must appear at the
SMODE and the DATA_CLK follows this with one more
change to low level in order to successfully complete the
protocol.
handbook, full pagewidth
MHB697
DATA_CLK
(input at pin 9)
SMODE
(input at pin 10)
TOUT
(output at pin 22)
1
2
3
4
5
stop
condition
status bit
start
condition
T1
T0
Fig.4 Protocol used to set UZZ9000 into trim mode.
Table 3
Definition of the trim interface signals
How to enter the trim mode
The status bits to be transmitted to the UZZ9000 are shown in Table 4. Note that a complete protocol has to be sent
before normal operation can be resumed. The trim mode can also be exited by resetting the device. After entering one
of the trim modes and provided there is a dynamic input signal, a square wave output is visible at the terminal T
OUT
(pin 22).
PARAMETER
MIN.
NOM.
MAX.
UNIT
UZZ9000 supply voltage
low level of DATA_CLK, SMODE
high level of DATA_CLK, SMODE
rise and fall time of DATA_CLK and SMODE signal
edges (10 to 90% V
DD
) and (90 to 10% V
DD
)
DATA_CLK frequency
4.5
0
95
8
5
5.5
5
100
V
%V
DD
%V
DD
ns
0.1
1
MHz
相關PDF資料 |
PDF描述 |
|---|---|
| UZZ9001 | Sensor Conditioning Electronic(傳感器調節芯片) |
| Z-15GD-B | BASIC SWITCH |
| Z-15GD-B7 | ENDLAGENSCHALTER NACHLAUFSTOESSEL KURZ |
| Z-15GK355-B7 | ENDLAGENSCHALTER STOESSEL ABGEDICHTET |
| Z-15GL2-B | BASIC SWITCH |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UZZ9001 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Sensor Conditioning Electronic |
| UZZ9001,118 | 功能描述:ELECTRONIC CONDITIONING SENSOR RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| UZZ9113 | 制造商:Microsemi Corporation 功能描述:DIODE - Bulk |
| v | 制造商:Airpax 功能描述: |
| V 1 | 制造商:Lascar Electronics 功能描述:VOLTMETER, LCD, 3.5 DIGIT, DIL CONNECTION, 200mV READING 制造商:Lascar Electronics 功能描述:LCD 3.5 DIGIT PACK OF 10 |
發布緊急采購，3分鐘左右您將得到回復。