- 您現在的位置：買賣IC網 > PDF目錄382729 > UZZ9001 (NXP SEMICONDUCTORS) Sensor Conditioning Electronic(傳感器調節芯片) PDF資料下載
參數資料
| 型號： | UZZ9001 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Sensor Conditioning Electronic(傳感器調節芯片) |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO24 |
| 封裝： | SO-24 |
| 文件頁數： | 5/16頁 |
| 文件大小： | 72K |
| 代理商： | UZZ9001 |
2000 May 19
5
Philips Semiconductors
Preliminary specification
Sensor Conditioning Electronic
UZZ9001
handbook, full pagewidth
MHB698
ADC1
DECIMATION
FILTER
ALU
SPI
CLK
CS
data
DATA-CLK
SMODE
CONTROL
OSCILLATOR
+
VO1
VO1
ADC2
RESET
UZZ9001
reset
DECIMATION
FILTER
+
VO2
VO2
Fig.1 Block diagram.
The following list gives a short description of the relevant
block functions:
1.
The ADC block contains two Sigma Delta AD
converters, sensor offset correction circuitry and the
circuitry required for the sensitivity and offset
adjustment of the chip output voltage curve.
Two digital low pass decimation filters convert the low
resolution high speed bit stream coming from the ADC
Sigma Delta converters into a low speed digital word.
The ALU block derives an angle value from the two
digital inputs using the CORDIC algorithm.
The SPI converts the output of the ALU block to a SPI
compatible 16 bit word.
The CONTROL block provides the clock and the
control signals for the chip.
The RESET block supplies a reset signal during
power-up and power-down when the power supply is
below a certain value.
The Oscillator unit generates the master clock.
2.
3.
4.
5.
6.
7.
Serial Peripheral interface (SPI)
The UZZ9001 provides an interface to SPI compatible
devices, and as a slave node functions in one operational
mode only. For Motorola SPI devices, this mode is
selected by setting CPHA to 1 and CPOL to 1. In this
transfer mode, data bits are sampled by the master using
the leading edge of the clock as shown in Figure 2. The
falling edge indicates that the next data bit has to be
provided by the slave device (shift operation).
AnadvantageofthismodeisthattheCSinputtogglesonly
once between every two sensor data bytes (see Fig.3).
Data transmission can be stopped by the user at any time.
The leading edge of the CS input initialises the SPI shift
register allowing the start of a complete new transmission.
If the CS line is held active low during stop of transmission,
resumption of transmission can be made without loss of
data
相關PDF資料 |
PDF描述 |
|---|---|
| Z-15GD-B | BASIC SWITCH |
| Z-15GD-B7 | ENDLAGENSCHALTER NACHLAUFSTOESSEL KURZ |
| Z-15GK355-B7 | ENDLAGENSCHALTER STOESSEL ABGEDICHTET |
| Z-15GL2-B | BASIC SWITCH |
| Z15GQ21-B7 | ENDLAGENSCHALTER QUERROLLENSTOESSEL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UZZ9001,118 | 功能描述:ELECTRONIC CONDITIONING SENSOR RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| UZZ9113 | 制造商:Microsemi Corporation 功能描述:DIODE - Bulk |
| v | 制造商:Airpax 功能描述: |
| V 1 | 制造商:Lascar Electronics 功能描述:VOLTMETER, LCD, 3.5 DIGIT, DIL CONNECTION, 200mV READING 制造商:Lascar Electronics 功能描述:LCD 3.5 DIGIT PACK OF 10 |
| V 1 (PK OF 10) | 制造商:Lascar Electronics 功能描述:LCD VOLTMETER, 3-1/2 DIGIT, 7-12VDC, 200MVDC MEAS RANGE 制造商:Lascar Electronics 功能描述:PANEL DISPLAY, VOLTMETER, LCD, 7V-12V; No. of Digits / Alpha:3-1/2; Meter Function:DC Volts; Meter Range:0mV to 200mV; Digit Height:6.3mm; Panel Cutout Height:15mm; Panel Cutout Width:31mm; Supply Voltage Range:7V DC to 12V DC |
發布緊急采購，3分鐘左右您將得到回復。