
Specifications subject to change without notice. All dimensions in inches. Copyright 1998 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630-851-5040
www.conwin.com
3.3V Surface Mount
Oscillator
VPLD54TEM
VCXO
The Connor-Winfield VPLD54TEM is a 3.3V
Voltage Controlled Crystal Oscillator (VCXO)
with Differential LVPECL outputs and Enable/
Disable function. The VPLD54TEM is designed
for use with PLL systems in SONET/SDH sys-
tems requiring low jitter and tight stability. No
uses of multiplication schemes are used in this
oscillator design.
Operating Specifications
Minimum
Nominal
Parameter
Center Frequency (Fo)
Maximum
Units
Notes
400.0
625.0
622.08
644.531250
-
-
3.3
-
-
-
MHz
Total Frequency Tolerance
Operating Temperature Range
Supply Voltage (Vcc)
Supply Current (Icc)
Jitter:
(BW=10 Hz to 20 MHz)
(BW=12 kHz to 80 MHz)
SSB Phase Noise
@ 100 Hz offset
@ 1 kHz offset
@ 10 kHz offset
@ 100 kHz offset
-20
0
3.135
-
20
70
ppm
°C
Vdc
mA
1
3.465
100
-
-
-
-
5
1
ps RMS
-
-
-
-
-60
-90
-130
-135
-
-
-
-
dBc/Hz
Absolute Maximum Ratings
Minimum
Nominal
-40
-0.5
-0.5
Parameter
Storage Temperature
Supply Voltage (Vcc)
Control Voltage (Vc)
Maximum
85
7.0
7.0
Units
°C
Vdc
Vdc
Notes
-
-
-
Features:
Low Profile, Surface Mount Package
3.3V Operation
Low Jitter <1pS RMS
Total Frequency Tolerance ±20 ppm
Temperature Range 0° to 70°C
Differential LVPECL Outputs
Enable / Disable Function
VPLD54TEM - 622.08 MHz
VCXO
SERIES
CENTER
FREQUENCY
Notes:
1. Inclusive of calibration @25°C, frequency stability vs. temperature, supply and load
variations, shock vibration and aging for ten years. Control voltage (Vc) = 1.65 Vdc.
2. Control voltage for (Fo) = 1.65 Vdc Typical. Positive Transfer Function
3. When oscillator is disabled the true output is in a low state (Vol) and the
complementary output is in the high state (VoH)
4. 50 ohm termination into Vcc-2V or Thevein equivalent.
Ordering Information
Bulletin
Vx387
1 of 2
Page
Revision
02
Date
14 January 2003
US Headquarters:
630-851-4722
European Headquarters:
+353-61-472221
Input Characteristics
Minimum
0.3
±25
-10
-
10
-
2.275
Parameter
Control Voltage Range (Vc)
Absolute Pull Range (APR)
Monotonic Linearity
Input Impedance
Modulation Bandwidth (3dB)
Enable Input Voltage (Low) (Vil)
Disable Input Voltage (High) (Vih)
Nominal
1.65
-
-
50K
-
-
-
Maximum
3.0
-
10
-
-
1.68
-
Units
Vdc
ppm
%
Ohm
kHz
Notes
2
Vdc
3
Low Voltage PECL Output Characteristics
Minimum
Nominal
-
2.275
-
45
Parameter
Load
Voltage: High (Voh)
Low (Vol)
Duty Cycle at 50% Level
Maximum
50
-
1.68
55
Units
Ohms
Notes
4
-
-
-
Vdc
50
%