- 您現在的位置：買賣IC網 > PDF目錄376444 > X80000 (Intersil Corporation) Smart Power Plug Penta-Power Sequence Controller with Hot Swap PDF資料下載
參數資料
| 型號： | X80000 |
| 廠商： | Intersil Corporation |
| 英文描述： | Smart Power Plug Penta-Power Sequence Controller with Hot Swap |
| 中文描述： | 智能電源插頭五-序控制器電源熱插拔 |
| 文件頁數： | 1/37頁 |
| 文件大小： | 695K |
| 代理商： | X80000 |
當前第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
1
FN8148.0
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143
Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2005. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
X80000, X80001
Smart Power Plug
Penta-Power
Sequence Controller with Hot Swap
The X80000 contains three major functions: a power
communications controller, a power sequencing controller,
and a hotswap controller.
The power communications controller allows smart power
supply control via the backplane using the SMBus protocol.
The system can check for voltage, current, and
manufacturing ID compliance before board insertion. The
power distribution network can monitor the status of the
negative voltage supply, DC voltage supplies, and hardshort
events by accessing the Fault Detection Register and
General Purpose EEPROM of the device. Each device has a
unique slave address for identification.
The power sequencer controller time sequences up to five
DC-DC modules. The X80000 allows for various hardwired
configurations, either parallel or relay sequencing modes.
The power good, enable and voltage good signals provide
for flexible DC-DC timing configurations. Each voltage
enable signal has a programmable delay. In addition, the
voltage good signals can be monitored remotely via the fault
detection register (thru the SMBus).
The hot swap controller allows a board to be safely inserted
and removed from a live backplane without turning off the
main power supply. The X80000 family of devices offers a
modular, power distribution approach by providing flexibility
to solve the hotswap and power sequencing issues for
insertion, operations, and extraction. Hardshort Detection
and Retry with Delay, Noise filtering, Insertion Overcurrent
Bypass, and Gate Current selection are some of the
programmable features of the device.
During insertion, the gate of an external power MOSFET is
clamped low to suppress contact bounce. The
undervoltage/overvoltage circuits and the power on reset
circuitry suppress the gate turn on until the mechanical
bounce has ended. The X80000 turns on the gate with a
user set slew rate to limit the inrush current and incorporates
an electronic circuit breaker set by a sense resistor. After the
load is successfully charged, the PWRGD signal is asserted;
indicating that the device is ready to power sequence the
DC-DC power bricks.
Features
Integrates Three Major Functions
- Smart Power Plug communications
- Programmable power sequencing
- Programmable Hot Swap controller
Smart Power Plug
- Intelligent board insertion allows verification of board
and power supply resources prior to system insertion.
- Fault detection register records the cause of the faults
- Soft extraction
- Soft re-insertion
- Remote gate shutdown/turn on
- Power ID/manufacturing ID memory (2kb of EEPROM)
Programmable Power Sequencing
- Sequence up to 5 DC/DC converters.
- Four independent voltage enable pins
- Four programmable time delay circuits
- Soft Power Sequencing - restart sequence without
power cycling.
Hot Swap Controller
- Programmable overvoltage and undervoltage protection
- Undervoltage lockout for battery/redundant supplies
- Programmable slew rate for external FET gate control
- Electronic circuit breaker - overcurrent detection and
gate shut-off
- Programmable overcurrent limit during Insertion
- Programmable hardshort retry with retry failure flag
- Typically operates from -30V to -80V. Tolerates
transients to -200V (limited by external components)
Available Packages
- 32-lead Quad No-Lead Frame (QFN)
Applications
-48V Hot Swap Power Backplane/Distribution Central
Office, Ethernet for VOIP
Card Insertion Detection
Power Sequencing DC-DC/Power Bricks
IP Phone Applications
Databus Power Interfacing
Custom Industrial Power Backplanes
Distributed Power Systems
Data Sheet
March 18, 2005
相關PDF資料 |
PDF描述 |
|---|---|
| X80001 | Smart Power Plug Penta-Power Sequence Controller with Hot Swap |
| X80012Q32I | 14 STR PE BLK RoHS Compliant: Yes |
| X80010Q32I | Penta-Power Sequence Controller with Hot swap and System Management |
| X80013Q32I | Connector Wall Plate; Color:Almond; Leaded Process Compatible:Yes; Contact Termination:IDC; No. of Ports:3 RoHS Compliant: Yes |
| X80011Q32I | Penta-Power Sequence Controller with Hot swap and System Management |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X80000Q32I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Smart Power Plug Penta-Power Sequence Controller with Hot Swap |
| X80001 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Smart Power Plug Penta-Power Sequence Controller with Hot Swap |
| X80001Q32I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Smart Power Plug Penta-Power Sequence Controller with Hot Swap |
| X80010 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Penta-Power Sequence Controller with Hot swap and System Management |
| X80-01-01 | 制造商:MOFLASH SIGNALLING 功能描述:XENON BEACON,AMB,SMALL |
發布緊急采購，3分鐘左右您將得到回復。