
3
FN6311.0
June 28, 2006
Absolute Maximum Ratings
Thermal Information
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage at any Digital Interface Pin
with Respect to GND . . . . . . . . . . . . . . . . . . . . . -0.3V to VCC+0.3
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6V
Voltage at any DCP pin with Respect to GND . . . . . . . -0.3V to VCC
Lead Temperature (Soldering, 10s) . . . . . . . . . . . . . . . . . . . . . 300°C
IW (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
Latchup (Note 4) . . . . . . . . . . . . . . . . . . Class II, Level B @+125°C
ESD (HBM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5kV
(CDM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1kV
Thermal Resistance (Typical, Note 3)
θJA (°C/W)
8 Lead MSOP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
130
Maximum Junction Temperature (Plastic Package). . . . . . . . . .150°C
Recommended Operating Conditions
Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 125°C
VCC Voltage for DCP Operation . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -3mA to 3mA
Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mW
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
3.
θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
4. Jedec Class II pulse conditions and failure criterion used. Level B exceptions are: using a max positive pulse of 6.5V on the SHDN pin, and using
a max negative pulse of -1V for all pins.
Analog Specifications
Over recommended operating conditions unless otherwise stated.
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
TYP
(NOTE 5)
MAX
UNIT
RTOTAL
End-to-End Resistance
W option
10
k
U option
50
k
End-to-End Resistance Tolerance
-20
+20
%
End-to-End Temperature Coefficient
W option
±50
ppm/°C
(Note 14)
U option
±80
ppm/°C
(Note 14)
RW
(Note 14)
Wiper Resistance
VCC = 3.3V @ 25°C,
wiper current = VCC/RTOTAL
70
CW
(Note 14)
Wiper Capacitance
25
pF
ILkgRW
Leakage on RW Pin
Voltage at pin from GND to VCC
24
A
VOLTAGE DIVIDER MODE ( measured at RW, unloaded)
INL
(Note 10)
Integral Non-linearity
-1
1
LSB
(Note 6)
DNL
(Note 9)
Differential Non-linearity
Monotonic over all tap positions
-0.5
0.5
LSB
(Note 6)
ZSerror
(Note 7)
Zero-scale Error
W option
0
1
5
LSB
(Note 6)
U option
0
0.5
2
FSerror
(Note 8)
Full-scale Error
W option
-5
-1
0
LSB
(Note 6)
U option
-2
-1
0
TCV
(Notes 11, 14)
Ratiometric Temperature Coefficient
DCP register set to 40 hex
±4
ppm/°C
ISL22419