- 您現在的位置：買賣IC網 > PDF目錄68803 > 70IMX7-24-24-9 (POWER-ONE INC) 2-OUTPUT 7.2 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | 70IMX7-24-24-9 |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 2-OUTPUT 7.2 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | 2 X 1 INCH, 10.50 MM HEIGHT, MA-9 |
| 文件頁數： | 15/15頁 |
| 文件大小： | 213K |
| 代理商： | 70IMX7-24-24-9 |
IMX 7 DC/DC Series Data Sheet
7W Board Mountable Converter
REV. OCT 01, 2003
9/15
IMX SERIES
70
100
Uo [%]
t [ms]
05041
8.5
60.5
overload short circuit condition
switch-off
40
50
60
70
80
90
h
[%]
05052
25
50
75
100
Po
Po nom
[%]
U i nom
U i max
U i min
Fig. 10
Overload switch-off (hiccup mode). Typical values.
Frequency of pulses: 16.5 Hz, puls duration: 8.5 ms.
Fig. 11
Efficiency versus input voltage and load. Typical values
(40 IMX 7-12-12).
Adjustable Output Voltage (R input)
As a standard feature, the IMX 7 single and double output
units offer adjustable output voltage(s) by using the control
input R. If the R pin is left open circuit the output voltage is
set to Vo nom. The output voltage is adjustable in the range
75...105 % of Vo nom.The circuit works for single and double
output units in a different way. For output voltages Vo >
Vo nom, the minimum input voltage Vi min (see: Electrical In-
put Data) increases proportionally to Vo/Vo nom.
Single output units:
The R input is referenced to the secondary side of the con-
verter. Adjustment of the output voltage is possible by
means of either an external resistor or a voltage source.
a) Adjustment by means of an external resistor Rext1:
Depending upon the value of the required output voltage,
the resistor shall be connected
either: Between the R pin and Vo– to achieve an output
voltage adjustment range of approximately
Vo = 75...100 % Vo nom. (85...100% for 3.3 V outputs)
Vo
Rext1 = 4 k –––––––––
Vo nom – Vo
or: Between the R pin and Vo+ to achieve an output volt-
age range of approximately Vo = 100...105 % Vo nom.
(Vo – 2.5 V)
Rext2 = 4 k –––––––––––––––––––
2.5 V (Vo/Vo nom – 1)
Auxiliary Functions
Inhibit Function
The output(s) of the converter may be enabled or disabled
by means of a logic signal (TTL, CMOS, etc.) applied to the
inhibit pin. No output voltage overshoot will occur when the
unit is turned on. If the inhibit function is not required the
inhibit pin should be connected to Vi– to enable the output
(active low logic, fail safe).
Converter operating:
–10 V...0.8 V
Converter inhibited
or inhibit pin left open:
2.4 V...Vi max
(<75 V for 70/110 IMX 7)
Fig. 12
If the inhibit is not used the inhibit pin should be con-
nected to Vi–
Vi+
Vi –
i
06070
相關PDF資料 |
PDF描述 |
|---|---|
| 70IMX7-05-9 | 1-OUTPUT 6.1 W DC-DC REG PWR SUPPLY MODULE |
| 70IMX7-05-8G | 1-OUTPUT 6.1 W DC-DC REG PWR SUPPLY MODULE |
| 110IMX7-03-8Z | 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
| 110IMX7-12-12-8Z | 2-OUTPUT 7.2 W DC-DC REG PWR SUPPLY MODULE |
| 110IMX7-05-8Z | 1-OUTPUT 6.1 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 70J00000Z | 功能描述:保險絲 3.5A Black/White 125VAC 300VDC RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485 |
| 70J1G032P502U | 制造商:Honeywell Sensing and Control 功能描述: |
| 70J1G032P504A | 制造商:Honeywell Sensing and Control 功能描述: |
| 70J1G032S103A | 功能描述:工業移動感應器和位置傳感器 RESISTIVE & OPTICAL RoHS:否 制造商:Honeywell 輸出類型:Analog - Current 電壓額定值:12 VDC to 30 VDC 線性:+/- 0.0011 % 溫度范圍:- 40 C to + 85 C 總電阻: 容差: 類型:Rotary Sensor |
| 70J1G032S103U | 功能描述:工業移動感應器和位置傳感器 RESISTIVE & OPTICAL RoHS:否 制造商:Honeywell 輸出類型:Analog - Current 電壓額定值:12 VDC to 30 VDC 線性:+/- 0.0011 % 溫度范圍:- 40 C to + 85 C 總電阻: 容差: 類型:Rotary Sensor |
發布緊急采購，3分鐘左右您將得到回復。