- 您現在的位置：買賣IC網 > PDF目錄68811 > 71M6521DE-IMR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, QCC68 PDF資料下載
參數資料
| 型號： | 71M6521DE-IMR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC68 |
| 封裝： | LEAD FREE, LQFN-68 |
| 文件頁數： | 36/103頁 |
| 文件大小： | 1691K |
| 代理商： | 71M6521DE-IMR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁
71M6521DE/71M6521FE
Energy Meter IC
DATA SHEET
OCTOBER 2010
Page: 38 of 103
2005-2010 Teridian Semiconductor Corporation
v1.1
A Maxim Integrated Products Brand
19-5370; 10/10
On-Chip Resources
Oscillator
The 71M6521DE/FE oscillator drives a standard 32.768kHz watch crystal. These crystals are accurate and do not require a
high-current oscillator circuit. The 71M6521DE/FE oscillator has been designed specifically to handle these crystals and is
compatible with their high impedance and limited power handling capability.
PLL and Internal Clocks
Timing for the device is derived from the 32.768kHz oscillator output. On-chip timing functions include the MPU master clock, a
real time clock (RTC), and the delta-sigma sample clock. In addition, the MPU has two general counter/timers (see MPU
section).
The ADC master clock, CKADC, is generated by an on-chip PLL. It multiplies the oscillator output frequency (CK32) by 150.
The CE clock frequency is always CK32 * 150, or 4.9152MHz, where CK32 is the 32kHz clock. The MPU clock frequency is
determined by MPU_DIV and can be 4.9152MHz *2
-MPU_DIV Hz where MPU_DIV varies from 0 to 7 (MPU_DIV is 0 on power-
up). This makes the MPU clock scalable from 4.9152MHz down to 38.4kHz. The circuit also generates a 2x MPU clock for use
by the emulator. This clock is not generated when ECK_DIS is asserted by the MPU.
The setting of MPU_DIV is maintained when the device transitions to BROWNOUT mode, but the time base in BROWNOUT
mode is 28,672Hz.
Real-Time Clock (RTC)
The RTC is driven directly by the crystal oscillator. It is powered by the net V2P5NV (battery-backed up supply). The RTC
consists of a counter chain and output registers. The counter chain consists of seconds, minutes, hours, day of week, day of
month, month, and year. The RTC is capable of processing leap years. Each counter has its own output register. Whenever
the MPU reads the seconds register, all other output registers are automatically updated. Since the RTC clock is not coherent
to the MPU clock, the MPU must read the seconds register until two consecutive reads are the same (requires either 2 or 3
reads). At this point, all RTC output registers will have the correct time. Regardless of the MPU clock speed, RTC reads
require one wait state.
RTC time is set by writing to the RTC registers in I/O RAM. Each byte written to RTC must be delayed at least 3 RTC cycles
from any previous byte written to RTC. Hardware RTC write protection requires that a write to address 0x201F occur before
each RTC write. Writing to address 0x201F opens a hardware ‘enable gate’ that remains open until an RTC write occurs and
then closes. It is not necessary to disable interrupts between the write operation to 0x201F and the RTC write because the
‘enable gate’ will remain open until the RTC write finally occurs
Two time correction bits, RTC_DEC_SEC and RTC_INC_SEC are provided to adjust the RTC time. A pulse on one of these bits
causes the time to be decremented or incremented by an additional second at the next update of the RTC_SEC register. Thus,
if the crystal temperature coefficient is known, the MPU firmware can integrate temperature and correct the RTC time as
necessary.
Temperature Sensor
The device includes an on-chip temperature sensor for determining the temperature of the bandgap reference. The MPU may
request an alternate multiplexer frame containing the temperature sensor output by asserting MUX_ALT. The primary use of
the temperature data is to determine the magnitude of compensation required to offset the thermal drift in the system (see
section titled “Temperature Compensation”).
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6521FE-IM/F | SPECIALTY ANALOG CIRCUIT, QCC68 |
| 71M6521FE-IGT/F | SPECIALTY ANALOG CIRCUIT, QFP64 |
| 71M6531D-IMR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
| 71M6532D-IGTR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
| 71M6532F-IGT/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6521DH | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Energy Meter ICs |
| 71M6521DH-IGT/F | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Energy Meter ICs |
| 71M6521DH-IGTR/F | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Energy Meter ICs |
| 71M6521FE | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Energy Meter IC |
| 71M6521FE-DB | 功能描述:開發板和工具包 - 8051 71M6521FE Demo Brd RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。