- 您現在的位置：買賣IC網 > PDF目錄68811 > 71M6521FE-IMR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, QCC68 PDF資料下載
參數資料
| 型號： | 71M6521FE-IMR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC68 |
| 封裝： | LEAD FREE, LQFN-68 |
| 文件頁數： | 45/103頁 |
| 文件大?。?/td> | 1691K |
| 代理商： | 71M6521FE-IMR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁
71M6521DE/71M6521FE
Energy Meter IC
DATA SHEET
OCTOBER 2010
Page: 46 of 103
2005-2010 Teridian Semiconductor Corporation
v1.1
A Maxim Integrated Products Brand
19-5370; 10/10
Hardware Watchdog Timer
In addition to the basic watchdog timer included in the 80515 MPU, an independent, robust,
fixed-duration, watchdog timer (WDT) is included in the device. It uses the RTC crystal
oscillator as its time base and must be refreshed by the MPU firmware at least every 1.5
seconds. When not refreshed on time the WDT overflows, and the part is reset as if the
RESET pin were pulled high, except that the I/O RAM bits will be in the same state as after
a wake-up from SLEEP or LCD modes (see the I/O RAM description for a list of I/O RAM
bit states after RESET and wake-up). 4100 oscillator cycles (or 125ms) after the WDT
overflow, the MPU will be launched from program address 0x0000.
A status bit, WD_OVF, is set when WDT overflow occurs. This bit is powered by the non-
volatile supply and can be read by the MPU to determine if the part is initializing after a
WDT overflow event or after a power-up. After it is read, MPU firmware must clear
WD_OVF. The WD_OVF bit is cleared by the RESET pin
There is no internal digital state that deactivates the WDT. For debug purposes, however,
the WDT can be disabled by tying the V1 pin to V3P3 (see Figure 37). Of course, this also
deactivates V1 power fault detection. Since there is no method in firmware to disable the
crystal oscillator or the WDT, it is guaranteed that whatever state the part might find itself
in, upon WDT overflow, the part will be reset to a known state.
Asserting ICE_E will also deactivate the WDT. This is the only method that will disable the
WDT in BROWNOUT mode.
In normal operation, the WDT is reset by periodically writing a one to the WDT_RST bit. The
watchdog timer is also reset when the internal signal WAKE=0 (see section on Wake Up
Behavior).
Figure 14: Functions defined by V1
Program Security
When enabled, the security feature limits the ICE to global flash erase operations only. All other ICE operations are blocked.
This guarantees the security of the user’s MPU and CE program code. Security is enabled by MPU code that is executed in a
32 cycle preboot interval before the primary boot sequence begins. Once security is enabled, the only way to disable it is to
perform a global erase of the flash, followed by a chip reset.
The first 32 cycles of the MPU boot code are called the preboot phase because during this phase the ICE is inhibited. A read-
only status bit, PREBOOT, identifies these cycles to the MPU. Upon completion of preboot, the ICE can be enabled and is
permitted to take control of the MPU.
SECURE, the security enable bit, is reset whenever the chip is reset. Hardware associated with the bit permits only ones to be
written to it. Thus, preboot code may set SECURE to enable the security feature but may not reset it. Once SECURE is set, the
preboot code is protected and no external read of program code is possible
Specifically, when SECURE is set:
The ICE is limited to bulk flash erase only.
Page zero of flash memory, the preferred location for the user’s preboot code, may not be page-erased by either
MPU or ICE. Page zero may only be erased with global flash erase.
Writes to page zero, whether by MPU or ICE are inhibited.
The
SECURE bit is to be used with caution! Inadvertently setting this bit will inhibit access to the part via the ICE
interface, if no mechanism for actively resetting the part between reset and erase operations is provided (see ICE
Interface description).
V3P3
V3P3 -
400mV
V3P3 - 10mV
VBIAS
0V
Battery
modes
Normal
operation,
WDT
enabled
WDT dis-
abled
V1
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6521DE-IGT/F | SPECIALTY ANALOG CIRCUIT, QFP64 |
| 71M6521FE-IGTR/F | SPECIALTY ANALOG CIRCUIT, QFP64 |
| 71M6521DE-IMR/F | SPECIALTY ANALOG CIRCUIT, QCC68 |
| 71M6521FE-IM/F | SPECIALTY ANALOG CIRCUIT, QCC68 |
| 71M6521FE-IGT/F | SPECIALTY ANALOG CIRCUIT, QFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6521-TGP1-68M | 制造商:Maxim Integrated Products 功能描述:Programmer Accessories Gang Programmer Base w/6521 Socket Brd |
| 71M6523-DB | 功能描述:開發板和工具包 - 8051 71M6521D Demo Brd RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
| 71M6523-IM | 功能描述:計量片上系統 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6523-IM/F | 功能描述:計量片上系統 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6523-IMR | 功能描述:計量片上系統 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。