- 您現在的位置：買賣IC網 > PDF目錄68812 > 71M6543GH-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6543GH-IGTR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 134/157頁 |
| 文件大小： | 2178K |
| 代理商： | 71M6543GH-IGTR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁當前第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
71M6543F/H and 71M6543G/GH Data Sheet
78
2008–2011 Teridian Semiconductor Corporation
v1.2
3.2.1
BRN Mode
In BRN mode, most non-metering digital functions are active (as shown in Table 62) including ICE, UART,
EEPROM, LCD and RTC. In BRN mode, the PLL continues to function at the same frequency as MSN
mode. It is up to the MPU to scale down the PLL (using PLL_FAST, I/O RAM 0x2200[4]) or the MPU
frequency (using MPU_DIV[2:0], I/O RAM 0x2200[2:0]) in order to save power.
From BRN mode, the MPU can choose to enter LCD or SLP modes. When system power is restored
while the 71M6543 is in BRN mode, the part automatically transitions to MSN mode.
The recommended minimum power configuration for BRN mode is as follows:
RCE0 = 0x00 (I/O RAM 0x2709[7:0]) - remote sensors disabled
LCD_BAT = 1 (I/O RAM 0x2402[7]) - LCD powered from VBAT
LCD_VMODE[1:0] = 0 (I/O RAM 0x2401[7:6]) - 5V LCD boost disabled
CE6 = 0x00 (I/O RAM 0x2106) - CE, RTM and CHOP are disabled
MUX_DIV[3:0] = 0(I/O RAM 0x2100[7:4]) - the ADC multiplexer is disabled
ADC_E = 0 (I/O RAM 0x2704[4]) - ADC disabled
VREF_CAL = 0 (I/O RAM 0x2704[7]) – Vref not driven out
VREF_DIS = 1 (I/O RAM 0x2704[6]) - Vref disabled
PRE_E = 0 (I/O RAM 0x2704[5] - pre-amp disabled
BCURR = 0 (I/O RAM 0x2704[3]) - battery 100A current load OFF
TMUX[5:0] = 0x0E (I/O RAM 0x2502[5:0]) – TMUXOUT output set to a dc value
TMUX2[4:0] = 0x0E (I/O RAM 0x2503[4:0]) – TMUXOUT2 output set to a dc value
CKGN = 0x24 (I/O RAM 0x2200) - PLL set slow, and MPU_DIV[2:0] (I/O RAM 0x2200[2:0]) set to maximum
TEMP_PER[2:0] = 6 (I/O RAM 0x28A0[2:0]) - temp measurement set to automatic every 512 s
TEMP_BSEL = 1 (I/O RAM 0x28A0[7]) - temperature sensor monitors VBAT
PCON |= 1 (SFR 0x87) - at the end of the main BRN loop, halt the MPU and wait for an interrupt
The baud rate registers are adjusted as needed
All unused interrupts are disabled
3.2.2
LCD Mode
LCD mode may be commanded by the MPU at any time by setting the LCD_ONLY control bit (I/O RAM
0x28B2[6]). However, it is recommended that the LCD_ONLY control bit be set by the MPU only after the
71M6543 has entered BRN mode. For example, if the 71M6543 is in MSN mode when LCD_ONLY is set,
the duration of LCD mode is very brief and the 71M6543 immediately 'wakes'.
In LCD mode, V3P3D is disabled, and the VBAT pin supplies the LCD current. Before asserting
LCD_ONLY mode, it is recommended that the MPU minimize PLL current by reducing the output
frequency of the PLL to 6.29 MHz (i.e., write PLL_FAST = 0, I/O RAM 0x2200[4]). The LCD boost system
requires a clock from the PLL for its operation. Thus, if the LCD boost system is enabled (i.e.,
LCD_VMODE[1:0] = 10, I/O RAM 0x2401[7:6]), then the PLL is automatically kept active during LCD
mode, otherwise the PLL is de-activated.
In LCD mode, the data contained in the LCD_SEG registers is displayed using the segment driver pins.
Up to two LCD segments connected to the pins SEGDIO22 and SEGDIO23 can be made to blink without
the involvement of the MPU, which is disabled in LCD mode. To minimize battery power consumption,
only segments that are used should be enabled.
After the transition from LCD mode to MSN or BRN mode, the PC (Program Counter) is at 0x0000, the
XRAM is in an undefined state, and configuration I/O RAM bits are reset (see Table 71 for I/O RAM state
upon wake). The data stored in non-volatile I/O RAM locations is preserved in LCD mode (the shaded
locations in Table 71 are non-volatile).
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6543GH-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 722BG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 722MG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 73M1903-IGV | SPECIALTY CONSUMER CIRCUIT, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6543GHT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk |
| 71M6543GHT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Tape and Reel |
| 71M6543G-IGT/F | 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6543G-IGTR/F | 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6543GT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KK, PRES TEMP SENSOR - Bulk |
發布緊急采購，3分鐘左右您將得到回復。