- 您現在的位置：買賣IC網 > PDF目錄68813 > 73S8010C-IM (TERIDIAN SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, QCC32 PDF資料下載
參數資料
| 型號： | 73S8010C-IM |
| 廠商： | TERIDIAN SEMICONDUCTOR CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 封裝： | 5 X 5 MM, QFN-32 |
| 文件頁數： | 24/27頁 |
| 文件大小： | 367K |
| 代理商： | 73S8010C-IM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁
73S8010C
Smart Card Interface
DATA SHEET
Page: 6 of 27
2005 TERIDIAN Semiconductor Corporation
Rev 1.2
I
2C-bus Write to Control Register:
I
2C-bus Write command to the control register follows the format shown below. After the START condition, the
master sends a slave address. This address is seven bits long followed by an eighth bit, which is an opcode bit
(R/
W) – a ‘zero’ indicates the master will write data to the control register. After the R/W bit, the ’zero’ ACK bit is
sent to the master by the device. The master now starts sending the 8 bits of data to the control register during
the DATA bits. After the DATA bits, the ‘zero’ ACK bit is sent to the master by the device. The master should send
the STOP condition after receiving this ACK bit.
1-78
91-8
9
ADDRESSbits
R/
W bit
ACKbit
DATAbits
ACKbit
STOP
condition
START
condition
SCL
SDA
MSB
LSB
Figure 2 - I
2C Bus Write Protocol
STATUS register
Power On Reset = 04h
Name
Bit
Description
PRES
0
Set when the card is present; reset when the card is not present.
PRESL
1
Set when PRES pin changes state (rising/falling edge), reset when the
status register is read. Generates an interrupt when set
I/O
2
Set when I/O is high; reset when I/O is low.
SUPL
3
Set when a voltage fault is detected; reset when the status register is
read. Generates an interrupt when set
PROT
4
Set when an over-current or over-heating fault has occurred during a
card session; reset when the status register is read. Generates an
interrupt when set
MUTE
5
Set during ATR when the card has not answered during the ISO 7816-3
time window (40000 card clock cycles); reset when the next session
begins or this register is read.
EARLY
6
Set during ATR when the card has answered before 400 card clock
cycles; reset when the next session begins or this register is read.
ACTIVE
7
Set when the card is active (VCC is on); reset when the card is inactive
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8010C-IM | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8010C-ILR | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8010C-ILR | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 73S8010C-IMR | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8010R-IM/F | SPECIALTY ANALOG CIRCUIT, QCC32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8010C-IM/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IM/F2 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IMR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IMR/F1 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IMR/F2 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
發布緊急采購，3分鐘左右您將得到回復。